- Support for Steinel IS 140-2 version 1.0.
- Support for Steinel L810 LED iHF version 1.1.

And then, starting with version 4.610 there is specified the above features were not included.

Meanwhile, the 620 version was released.

Can you please ley us know when you are going to add support the Steinel devices ? I assume there was a high number of requests since you have considered these features.

Thanks!

I am trying add the double swithc (FGS-224) in secure mode. I have tried to install the switch in non-secure mode and it works like a charm, with the issue that I can not associate directly to another existing device (since it is included in secure mode).

I start to see a pattern -- I have included device in secure mode previously without problems. Why is this now a problem.

If this problem is similiar as the other topic I had with HeatIt-devices, then I would appreciate if Fibaro could list at least the most significant known issues (provided that my assumption is correct, that this is just another example of my previous experienced issue with a HeatIt device).

When I tried to add the FGS-224 it stall after the logs below (then stalls after the last row on parameter 164).

Anyone having any similiar issue?

BR,

Erik

[22:48:32] Home Center in learning mode
[22:49:04] Device added
[22:49:04] Requesting neighbours, please wait...
[22:49:09] Requesting neighbours, please wait...
[22:49:10] Requesting neighbours done.
[22:49:10] Add node status protocol done
[22:49:10] Adding devices complete
[22:49:10] Adding devices complete
[22:49:16] ID 443: Setting value 1 for parameter 1
[22:49:16] ID 443: Setting value 0 for parameter 20
[22:49:16] ID 443: Setting value 0 for parameter 21
[22:49:16] ID 443: Setting value 0 for parameter 24
[22:49:16] ID 443: Setting value 0 for parameter 25
[22:49:16] ID 443: Setting value 0 for parameter 30
[22:49:16] ID 443: Setting value 100597760 for parameter 31
[22:49:16] ID 443: Setting value 33488896 for parameter 32
[22:49:16] ID 443: Setting value 50266112 for parameter 33
[22:49:16] ID 443: Setting value 83820544 for parameter 34
[22:49:16] ID 443: Setting value 600 for parameter 35
[22:49:16] ID 443: Setting value 15 for parameter 40
[22:49:16] ID 443: Setting value 15 for parameter 41
[22:49:16] ID 443: Setting value 0 for parameter 150
[22:49:16] ID 443: Setting value 0 for parameter 151
[22:49:16] ID 443: Setting value 0 for parameter 152
[22:49:16] ID 443: Setting value 0 for parameter 153
[22:49:16] ID 443: Setting value 5 for parameter 154
[22:49:16] ID 443: Setting value 5 for parameter 155
[22:49:16] ID 443: Setting value 255 for parameter 156
[22:49:16] ID 443: Setting value 0 for parameter 157
[22:49:16] ID 443: Setting value 99 for parameter 158
[22:49:16] ID 443: Setting value 255 for parameter 159
[22:49:16] ID 443: Setting value 0 for parameter 160
[22:49:16] ID 443: Setting value 99 for parameter 161
[22:49:16] ID 443: Setting value 0 for parameter 162
[22:49:16] ID 443: Setting value 0 for parameter 163
[22:49:16] ID 443: Setting value 0 for parameter 164

Any ideas how to upgrade?

I have another HC2 device for another house that I was able to upgrade from 4.620 to 4.630 inside my same LAN this morning, but my HC2 for my house is not showing anything.

Looking forward to see any tps/responses from Fibaro or other users.

looking into this I discovered that my HC2 at home isn't connecting remotely. It will connect locally on the home network, but not when I am coming in from outside the network.

In the fibaro ID webpage, it flickers between red and black in my devices showing it available and then unavailable.

I have given it a fixed IP, and it has always worked (6 years in) remotely. nothing has changed in my setup but it seems highly feesible its a fibaro issue.

In addition, my time was set to 2011 and when I try to set it to today, it wont go beyond 2021. Setting it to download time from the internet doesn't work.

Can anyone help.

Software is 4.620.

Thank you!

Is anybody seeing all the new features in Yubii 1.16 app........I am running an HC2 connected with 4.620 as I am not seeing any of these new features.

I have done the following.

• Deleted the Yubii app on the iPhone and reinstalled it 
• Restarted the HC2
• Interesting that when I deleted the Yubii app from the phone and reinstalled it I saw add devices on the Home Screen but it has since disappeared and I can not rename any devices from the app

Thanks

Beeker 

Recently two motion and one door sensors didn't send any reports  for few days, the batteries have dead (no voltage at all) while on UI the battery levels are 100% for all of them!

On one device I have used (on purpose) with low battery, still the UI shows 100%.

Any body else has same behavior?

I am trying to setup a heating system. I have included the Heatit Z-water in secure mode successfully. Now I am trying add the thermostats (Z-temp2) in secure mode. Since I want to control the z-water relays directly by association from the thermostats, I believe that if this is to work, both Z-temp2's as well as z-water need to be included in secure mode (or all of them in non-secure mode). Since I started with z-water and have now configured it I would like to avoid to re-install it from start (just because the thermostats can not be included in secure mode). Btw, I have tried to install the thermostats in non-secure mode and it works like a charm, with the issue that I can not associate directly to the z-water (since it is included in secure mode).

Now to my questions

- Is there anyone else having any issue including any other device (thermostat, switch, dimmer etc) in secure mode?

- I understand that z-temp2 shall be possible to add to HC2 in secure mode. Anyone else having the same experience? (Yes, I have tried multiple times, I have placed the thermostat literally less than a meter from the HC2 during paring, also including it in non-secure mode is working OK).

- During inclusion the following happens:

  o The home center logs the following when adding in secure mode:

[11:34:56] Home Center in learning mode
[11:35:09] Device added
[11:35:10] Requesting neighbours, please wait...
[11:35:13] Requesting neighbours done.
[11:35:13] Add node status protocol done
[11:35:13] Adding devices complete
[11:35:13] Adding devices complete

The Z-Temp2 display the "Inc" after that. No transfer of parameters and/or association group data.

Compare with adding the z-temp2 in non-secure mode:

[11:39:14] Home Center in learning mode
[11:39:19] Device added
[11:39:19] Requesting neighbours, please wait...
[11:39:23] Requesting neighbours done.
[11:39:23] Add node status protocol done
[11:39:23] Adding devices complete
[11:39:23] Adding devices complete
[11:39:25] ID 426: Received parameter 1 report, value = 900
[11:39:25] ID 426: Received parameter 2 report, value = 10
[11:39:25] ID 426: Received parameter 3 report, value = 10
[11:39:25] ID 426: Received parameter 4 report, value = 0
[11:39:26] ID 426: Received parameter 5 report, value = 0
[11:39:26] ID 426: Received parameter 6 report, value = 10
[11:39:26] ID 426: Received parameter 7 report, value = 1
[11:39:26] ID 426: Received parameter 8 report, value = 50
[11:39:26] ID 426: Received parameter 9 report, value = 3
[11:39:26] ID 426: Received parameter 10 report, value = 5
[11:39:26] ID 426: Received parameter 11 report, value = 50
[11:39:26] ID 426: Received parameter 12 report, value = 400
[11:39:26] ID 426: Received parameter 13 report, value = 0
[11:39:27] ID 426: Received parameter 14 report, value = 0
[11:39:27] ID 426: Received association report from group 1
[11:39:27] ID 426: Received association report from group 2
[11:39:27] ID 426: Received association report from group 3
[11:39:28] ID 426: Received association report from group 1
[11:39:28] ID 426: Received association report from group 2
[11:39:28] ID 426: Received association report from group 3
[11:39:37] ID 426: Device configuration finished
[11:39:37] ID 426: Device configuration finished

 Any help/support/solution is appreciated.

BR,

Erik

Zgłosiłem problem do serwisu braku możliwości upgradu wersji oprogramowania centralki HC2 z 3.600 do 4.620.

Nie mogłem zrobić tego sam bo został uszkodzony pendrive w centralce i żadna próba upgrade nie kończyła się powodzeniem.

Nadmieniam, że centralka znajduje się we Francji.

Na zgłoszenie odezwał się Pan Krzysztof Krynicki, który poprosił mnie o przygotowanie zdalnego dostępu.

Poświęcił On dość sporo czasu aby zdalnie upgradować centralkę. Centralka pracuje obecnie na ver 4.620.

Jeszcze raz dziękuje bardzo za pomoc i życzliwość.

Jacek Stark

when we get support for Steinel MotionSwitch LED Z-Wave?

Z-Wave Protocoll Version 5.3

Maybe in the next System Update?

Thanks for information.

cu,

karlk

Please login or register to see this attachment.

Please login or register to see this attachment.

I can not restor backup.

I made a recovery and I can log in but I can't do anything.

I can't put no new devices to my HC2, I can't make any scenes and I can't restore a backup.

What can I do? My HC2 does not working.

Help Me

Thank You

Please login or register to see this attachment.

Please login or register to see this image.

Please login or register to see this attachment.

But than the usual download and install dialog never appears (down below). Just that waiting image.

Please login or register to see this image.

I followed the steps to Recovery mode, but after recovery to default factory settings I noticed the HC2 is still using firmware 4.620 and still contains my latest configuration. But at least I am able to login using the url 192.168.81.1.

Only problem left: I cannot change the LAN settings to use DHCP.

When I browse to URL http://192.168.81.1/fibaro/en/configuration/network.html it is not opening that page

These configuration pages open:

http://192.168.81.1/fibaro/en/configuration/index.html

http://192.168.81.1/fibaro/en/configuration/users.html

http://192.168.81.1/fibaro/en/configuration/diagnostic.html

http://192.168.81.1/fibaro/en/configuration/connections.html

http://192.168.81.1/fibaro/en/configuration/location.html

http://192.168.81.1/fibaro/en/configuration/notification-center.html

http://192.168.81.1/fibaro/en/wizard/

http://192.168.81.1/fibaro/en/configuration/zwave.html

These pages don't open, and stay in some state to open the page

http://192.168.81.1/fibaro/en/configuration/backups.html

http://192.168.81.1/fibaro/en/configuration/network.html

I also followed the steps to use the API set network settings. The Get operation is giving error:

{ "reason": "Network error", "message": "Unable to read network settings. Please try again." }

Does anyone know how to resolve this? Recovery mode did not seem to reset it to factory settings. I am hoping to only resolve the access to LAN settings.

I just upgharde mu HC2 to the last version

and I can't remote access it by using fibaro id

my hc2 is rebooted

the upgrade goes good

i need your help

Best regards

Lahoucine

Pls. Fix it

Important notice:
All Z-Wave thermostats require performing soft reconfiguration to allow setting temperature from mobile app (not applicable to updates from version 4.611 beta). Sorry for the inconvenience.

New improvements:
- Added support for upcoming firmware updates of FIBARO Heat Controller (FGT-001).

Resolved issues:
- Unable to set temperature on thermostat using mobile app.
- In some cases the remote access connection is lost and not automatically restored.