I have two devices both have the same problem.

They worked with the ZW2 engine

When you change the setpoint and push set, set will grey out that it is set but the setpoint doesn't change.

The manual delay that is set will start counting.

Also the climate channel will not update the setpoint.

Only when you change the setpoint on the display of the device the setpoint changes and shows the correct setpoint in the Home Center interface.

I think this was also a bug in the ZW2 engine and was fixed a couple of updates back!

Also things such as battery status are not updated any longer: the system shows an "empty" battery altough fresh batteries has been installed.

Anybody any ideas on this ?

Please login or register to see this attachment.

Please login or register to see this attachment.

Please login or register to see this attachment.

I've tried factory resetting it several times, rebooting hc3, including/exluding etc. 

@m.roszak

Only it doesn't show the temperature sensor it self, so you do not know the actual temperature.

With the ZW2 engine the temperature sensor was avalible. 

After this update, my scenes are no longer triggering. As you can see in the video, the device is reporting its status - but the scene is not running. When I run the scene manually, the scene runs correctly (and the hue light is turned on).

The phone app shows all lights off, even though some are on. I can switch them on and off, no problem, but status are wrong.

Updated to ZW3 engine aswell.

No longer updates correct power usage aswell.

Takes a few seconds to react and then alot longer to complete. 

Switching from ZW2 to ZW3 by first exluding each device and then including takes very long per device. Also, 50% of the time the first inclusion attempt fails.

In France we usually need 4 digits, I don't know for other countries but I guess it should not be any different.

The actual price is 0.1544€, but I can only define 0.15€, see screenshot below.

=> Could you please add more digits in the next update ?

Thank you.

Please login or register to see this attachment.

Thank you for using our gateway! Be sure to update to the latest version to enjoy new features and improvements.


What's new:

Dashboard
Device state is now displayed on dashboard tile and sidebar for Base Shutter type devices.

Devices
Modified descriptions for device reconfiguration.**
Added info about needed waking up battery devices after requesting reconfiguration.**

Elero*
Possibility to use "Silent movement" in Scenes and Profiles for Elero RolMotion.

Nice*
Modified descriptions for device pairing process.
Reset/Reset all option added for device parameters configuration.
Adjusted list of supported notifications in device advanced configuration.
Changed model names of BiDi-Interface series devices.

Scenes
Creating scenes based on devices categories in Energy scenes.

Update
"Check for updates" button forces checking firmware update availability for devices.**


Bug fixes:

Cameras
Page refresh needed after saving camera configuration.

Dashboard
Unnecessary label "unknown" on Z-Wave shutters tiles.
Time does not update correctly in interface clock.

Devices
Disabling "Saving energy data to database" does not disable "Use stored energy".
Incorrect handling of "Save energy to database" and "Use stored energy in Energy Panel".
Possibility to disable "Saving energy data to database" for main energy meter.
Devices not visible currently on Settings page do not update their states correctly.
Graphs for FIBARO Thermostats (FGT-001) display incorrect setpoint values.
Cannot configure FGRGBWM-441 module in Input/Output mode.

Elero*
Device icon for Dimmer and Heater is not updated correctly.

Energy
Cannot remove data from main energy meter.
Energy cost calculation based on configured tariff works incorrectly.
Currency settings do not take effect without system reboot.

General
Setting the main energy meter does not enable saving energy data and using stored energy.

Network
Cannot connect to unprotected Wi-Fi network.

Other
Stability improvements related to "Serious problem detected" notification.
Changed translation for "Serious problem detected" notification.
Boot loop after updating to 5.092 Beta in some cases.

Plugins
In some cases Tedee Lock plugin loses connection with the device.

Profiles
Cannot set slider value for Quick Apps.

Quick Apps
Error 401 in the Mobile Application after opening a Quick App.**
fibaro.alert function does not work correctly.

Scenes
Average Consumption condition in Energy category does not work correctly.
Limits for Summary Balance conditions in Energy category are defined incorrectly.

Update
Cannot cancel Firmware Update process for battery device during "Waiting for wakeup".**

Voice Assistants
Issue with controlling thermostats from Alexa.


Known issues:

Z-Wave Engine 3.0
Some Z-Wave devices are not fully compatible with the new version of Z-Wave engine.
Gateway connection is not available in the new Z-Wave engine version.


* - does not apply to HC3L (Home Center 3 Lite)
** - applies only to Z-Wave Engine 3.0