I don't know if this is an issue due to the upgrade, or is something else.

I haven't added any new rooms or sensors for a while, a few days ago I added two new rooms and 3 new sensors, they do not show on the yubii app.

rooms I have renamed are showing fine, but new rooms do not appear.

Does anyone have any experience of this?

Phil

I found that Aeotec Home Energy Meters 1 phase can't be added on latest firmware 5.130.64. Tried several options:

   1) Z-Wave 2.0 Engine - without security - can't add - Interviewing finishes with Failed result and device "Not configured". Failed window freeze in BUI and need to reload page.

        Sometimes it's closes without prompt window for set device name and room - just back to BUI, but still "Not configured". Tried like 20 times - any luck

   2) Z-Wave 2.0 Engine with S0 security - adding successfully, but all parameters with zero values and can't set any value - device just freezes

   3) Z-Wave 3.0 Engine with S0 security - adding successfully with all settings, but device still not updating values to controller.

Tried with several firmwares of HEM-1 - 1.33, 1.35, 1.37

Tried several devices.

Tried on 3 different HC3 ( 1 - ZW 3.0, 2 and 3 - ZW 2.0 ) 

Tried factory reset.

Result the same, so, I trully sure that's firmware fail.

HEM 3 phase works more or less stable on those 3 HC3's , so, I think it's only HEM 1 phase glitch.

Will open case tomorrow or on Monday, but frankly, I don't expect any useful feedback from standard Fibaro support. Their scripts stuck on standard " try to factory reset" , " try to remove and try again "....

@m.roszak, maybe you have some info - any luck to have new firmware version soon ? Maybe with fixes of Energy Meters ?

In Ukraine we are very need that right now - to control all electric devices

Thank you in advance.

Please login or register to see this attachment.

I have a linked device used fot a half a year. Now the setpoint is not updating anymore. Not via a scene, the app or the browser.

In the app and via the scene it doesn't do anything. With the browser interface it gives a 404 Error:

Please login or register to see this attachment.

Setting te mode to Off and Cool works fine.

New beta update 5.131.52 is published, but no new forum thread about it here?

Is this beta published too early or you forget something or forum is again put on shelf until better days come? 😕

After install my HC3 will no longer boot, only the "house" icon is on.

There is no response to any og the two buttons, cannot enter recovery when holding power button. Seems completly dead...

"House" icon goes on when applying power to the unit and stays on..

Any suggestions?

I'm using my Home Center 3 for a couple of years now and am using ~100 different Z-Wave units, of which 90% are Fibaro modules.

I am not using the Z-Wave 3.0 engine, and I'm running version 5.130.64 for 2 weeks now.

My configuration has always been working without any issue, but yesterday the Z-Wave engine has partly crashed.

The HC3 did still receive all incoming data, like temperature values or on/off states. But I wasn't able to turn on/off any light.

First I tried a normal restart, but after 15 minutes it still said "starting services". Which normally is done much quicker.

Then I unplugged the HC3 from power. It then restarted quickly and the issue was resolved.

Questions:

1- Can I do anything to debug this issue? Are there any logs I can check?

2- Does anyone have any idea why this happened? Has it to do with this version? (5.130.64)

3- Can I add another HC3 to my setup as slave/secondary to avoid down time in the future? Could I then reboot the master HC3 while continuing network control using the slave HC3?

Thank you for your thoughts.

Please login or register to see this attachment.

When you develop a QuickApp, the devices properties list are not available.

Do you have the same issue ?

See blue icone 

Please login or register to see this attachment.

After the reset, all zigbee devices were deleted, but the humidity sensor ID remained in the linked devices.

After that, it became impossible to open the sprinkler device, error 404 occurs.

In editing the device, it is impossible to disable the missing sensor or select another one, the lists are disabled. It is also impossible to remove the sprinkler, a 404 error occurs.
Changing the device configuration via api also returns a 404 error.

How to remove absent sensor, or change linked device id to new device without full reset controller? 

On a attached screen - device 275 is not in the list of devices, but is in the list of linked devices.

Please login or register to see this attachment.

Please login or register to see this attachment.

Please login or register to see this attachment.

418 - new id humidity sensor after adding zigbee device

Please login or register to see this attachment.

Need support of zigbee and 

Bluetooth and templates Aeotec Multisensor 7,Aeotec ZWA039,LED Bulb 6 Multi-White.LED Bulb 6 Multi-rgb 

and hue varm and cold ligt

Restart solves the problem, but comes back again.

Please login or register to see this image.

Hi, I've noticed that the zigbee lights have a problem with on/off detection, often the icon is on but the panel is Off. It's very confusing. is there any solution to this? Thank you ( it seems to be happening after the last update)

Please login or register to see this attachment.

We installed the .64 and still have the same problem.

Also, when a particular heater is set for a certain temperature for let's say 45 minutes, only the 45 minutes is sent to the heater, not the new set temperature.

Who else encounters these problems?

The .64 version has a lot of problems with thermostats & climate zones.

If this continues like that we will have to roll back to a previous version...

A new hotfix is urgently needed. We loose too much time investigating, debugging and dealing with the situation.

5.130.64

Please login or register to see this attachment.

IMPORTANT NOTICE    

Version 5.130.64 is a hotfix of 5.130.45, it fixes following issues:

1. Some cases encountered system booting issue after update.
2. Scenes page hangs in some cases.
3. Stability improvements.
4. Thermostats do not always respond to manual setting from the climate panel.
5. Minor UX improvements. 

Main features:
    
1. Redesigned the way user access settings works

From now on, it is possible to grant access to devices and scenes by entire sections or rooms in the system.
Access to newly added devices and scenes will be automatically granted if an entire section or room is selected.
New user will automatically have access to the entire system from the beginning.
    
2. Scenes can be assigned to rooms

From now on, all types of scenes can be assigned to rooms, not just categories. 
    
3. Z-Wave devices exclusion wizard

Z-Wave exclusion is now available in new wizard style.
Additionally there is an option to start exclusion directly from failed inclusion process.
    
    
What's new:

Devices
    Added Gateway filter to devices list.
    Added possibility to filter out power metering devices from mobile application energy panel.
    Changed UI for icons selection.
    Heatit ZM Single Relay 16A support.
    Heatit ZM Thermostat 16A support.
    Heatit Z-Push Wall Controller support.
    Heatit Leakage Stopper support.

Network
    Automatic selection of network connection type in FTI if only one is available.

Nice*
    Optimized support for OXIBD module. 

Other
    Optimized trim of events database. 
    Performance improvements.
    Added system notification about potential performance loss due overheating.   
    Added possibility to clear all system notifications at once.     

Profiles
    Changed UI for icons selection. 

Quick Apps
    Power sensor device type added to QuickApps.
    Removed password saving option in browser for secret variables.

Rooms
    Changed UI for icons selection. 

Scenes
    Added validation for time inputs in block scenes.
    Devices used in scenarios and hidden later are now shown on the devices list.
    Scenes name limit is changed to 60 characters.
    Changed UI for icons selection. 

Update
    Translations support for devices Update Service.**
    Devices update now available using remote access.

Z-Wave
    Performance improvements.**

Bug fixes:

Alarm
    Some alarm scenes are not listed in Alarm tab.

Climate Panel
    Some devices set to "Hold" in manual mode returns to schedule anyway after 7 days.
    Climate zone deactivation does not work for some device types. 

Dashboard
    Favorite position label defined by user is not used on dashboard tiles and sidebar. 
    Alarm status "dots" on sensors tiles does not change color according to current zone state. 
    Scrolling long names does not always show the full text on device tiles. 

Devices
    Issue with displaying current values of bit-mask type configuration parameters.
    Cannot navigate to child device using "parent-child" tree when filters are enabled.
    Newly added device is not visible when filters are set.
    After adding a camera, modal for adding "other devices" stays open. 
    Wrong battery status for Sensative strip Guard 700 in some cases.
    Binary sensor cannot be used for Video Gate linked device. 
    Missing possibility to sort devices using battery level.
    Minor fixes in UX for new devices filters.
    Missing support for some actions related with color control (fading, enhancing, stop color change).
    HeatIt ZM Thermostat 16A set-point issue requires reconfiguration to work properly (introduced in 5.121.28 beta).

Elero*
    Devices are marked as dead during binding procedure in rare cases. 

Gateway Connection
    Incorrect role handling for FIBARO RGBW 1.
    Missing possibility to exclude device from slave gateway. 

Nice*
    Redundant "Stop" button for gates on control dialog in mobile application.
    Removed redundant step in "pairing a remote in gateway" binding process. 

Other
    Fixed Recovery UI issues in German language.
    Wrong display of "not used" RAM value in diagnostics. 
    Not saved system language during FTI in some cases. 
    Notifications creation time is calculated according to browser time, not system one.
    Mismatched translations when leaving Recovery mode.
    Some cases encountered system booting issue after update (introduced in 5.121.28 beta).
    Incorrect notification about HC3 gateway overheating (introduced in 5.121.28 beta).
    Newly added devices access issues for mobile app and web interface users (introduced in 5.121.28 beta).

Quick Apps
    Missing logs in console after page refresh.
    Quick App sprinkler device type is not supported in Garden Panel. 
    QuickApps content loading issue while using the remote connection (introduced in 5.121.28 beta).

Scenes
    Unnecessary popup with "unsaved changes" in some cases for Scenarios. 

Update
    Impossible to start second update for battery-operated device.**
    Last target in devices update stays in "In Progress" status even if whole process ended.**

Z-Wave
    Engine crash in some cases during multiple network management operations.**

Known issues:

Z-Wave Engine 3.0
    Some Z-Wave devices are not fully compatible with the new version of Z-Wave engine.
    Gateway connection is not available in the new Z-Wave engine version.

*  - does not apply to HC3L (Home Center 3 Lite)
** - applies only to Z-Wave Engine 3.0