Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


litfoo

Member
  • Posts

    13
  • Joined

  • Last visited

About litfoo

Profile information

  • Country
    United Kingdom
  • Gateway/s
    Home Center 2

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

litfoo's Achievements

Newbie

Newbie (1/8)

1

Reputation

  1. Hi all, I have just added a Neo Coolcam Motion Sensor (v2 I beliieve) to my HC2 and cannot see how I can change some of the default parameter values. For example, in the instructions it states I can change Parameter 11 to 0 to disable the LED from blinking red on motion detection However, on my Advanced tab for this motion sensor, it does not show any parameters Does anyone have any experience with the above and can advise? This is what the Advanced tab shows me presently Advanced settings page images Many thanks, litfoo
  2. Hi Gaaroriep, Would you mind sharing with Amcrest Models you are using and the paths that you used to get the images/stills? Thanks, litfoo
  3. Hi all, I managed to successfully add my Fibaro HC2 to Hass.io using the Fibaro component and all my Z-Wave devices are available in Hass.io I have also managed to group my lights. However, the state of my lights (on/off) are not being correctly displayed in the Hass.io front end. For example, I will turn on a light on Hass.io front end and the status would move from left to right (to indicate ON and this turn on my lights) but then will quickly move to the left (OFF position) in Hass.io - when in fact the lights are not OFF I really don’t understand why this weird behaviour exists so would be grateful if someone could shed some light and help me fix this. My motion sensors seem to be working fine and as expected. Many thanks, litfoo
  4. I am also running old Fibaro app on S10 with Android 9 App works with me for a few days, then suddenly I get 'Home Center not found' and I cannot access my HC2 Only remedy is to uninstall and re-install the app - which is obviously not ideal I have had to do this a couple of times already - all my other devices (android & iOS) are working fine so suggests an issue with S10 and/or Android 9
  5. Hi Sankotronic, Thanks so much for the guidance - it makes complete sense. I will have a significant amount of Dimmers, sensors etc. so will definitely follow your steps. Am looking forward to getting everything configured/setup and then look forward to creating some scenes. Awesome community here so am sure I'll be back asking many more questions litfoo
  6. many thanks for the information above - very helpful!
  7. I have set Parameter 80 to 0 - LED Inactive for the moment so there is no visual (colour) indicator. Where do I see 'event' logs of devices in the web interface? basically the logging of motion detection with timestamp etc. Also, is there a log showing all changes? changes to Lux and/or temperature too
  8. Thanks for that hTiger1 - makes sense and i now have it working
  9. Thanks I.Srodka, I changed to 4 - Red, then 'Save' but the radio button remained against 10 and blinking was not red I then tried 0 - LED inactive, then 'Save' (image below) - radio button still against 10 and blinking colours are same as before Any ideas what I may be doing wrong? I expected to choose say 4-Red, 'Save' - then the radio button is against 4 - Red and LED blinks red Many thanks, litfoo
  10. Hello there. Apologies if a newbie question - I have just added my first device into the HC2 and the other half was wondering why this device appeared to be going crazy Is there a way I can turn off the blinking light when the motion sensor reacts to motion? Is there a specific parameter I should be looking to control/edit Many thanks litfoo
  11. Hi all, I searched through the forum and there does not seem to be much recent activity regarding this. Has anyone had much success in using the Harmony Home Hub Extender with Fibaro HC2 ? http://www.logitech.com/en-us/product/harmony-home-hub-extender If so, please can you share the level of success - what you have manage to achieve etc.? Many thanks
  12. I am surprised not to see the Amcrest cameras here - for example the Amcrest Pro HD IP2M-841B Has anyone managed to successfully get this cam or any other Amcrest cameras to work - JPG and/or MJPG
×
×
  • Create New...