Domin2000

Another question: Must be the roller shutter in down position (closed) to make the calibration process start? Or can it be opend? In opened state (roller shutter is completely up) when calibration process starts the led is flashing red and the roller shutter does not come down. It seems it has a problem to come down. Another behaviour is when the roller shutter is closed: With the calibration process staring, the roller shutter moves upwards but is not coming down (led is flashing red) When it is flashing red i have to interrupt the process with the manual wall toggles.

@Trr You think positioning functionality has gone with a new firmware update on your fibaro roller shutter? I bought another 4 fibaros for my roller shutter. The same problem here. Only up and down works but no calibaration. What means the status on the fibaros when the led is red blinking?

@I.Srodka: I set up 130 as value but without any success. (but i did'nt modufy the value with motor operation time. it is still on 240 seconds) Still the same in the calibration process: The roller shutter goes up with green led, comes to its end position, then you hear a "click" then the red Led is blinking but the shutter does not move down. You have switche manually the toogles in the wall to abort the calibration process. i have bought another 4 fibaro roller shutter for my other windows. Maybe i try a different one on other window . Maybe i have to reset the fibaro module to factory settings?

@I.Srodkabut i have a general question: Why is the default value for configmotordetection only 10 Watts? Tje most roller shutters takes about 100 Watts in operation mode... i dont think roller shutters only take 10 watts of power..? Or do i missunterstand you?

@I.Srodka I measured up power with 151 Watts and down power 142 Watts Over the fibaro shutter. Idle is 0.0 Watts (Endposition). So the max difference between idle and operating is 151. So i have to Change the value to 151 from the standard 10? @TRicky Yes, they must have limit switches. It is exactly how you described: When i toggle the manual switches in the wall up or down position and leave them and the roller shutter comes to the endposition then automatically on S1 /S2 there is no voltage on these fibaro-connections. I am using simple manual toggles.

@Sjekke The brand is: Geiger Antriebstechnik. It is a German manufacturer. Motor Model: GEIGER-SOLIDline and the motor controller is GEIGER-SoftPerfection/-Zero (GU45..E03) Any experience on this?

@Sjekke OK i will ask my polish house manufacturer Danwood. Maybe they know what motors are buildt in.

@I.Srodka So you suggest to decrease the Parameter 18 value to a smaller size than 10W, maybe going from 9 on to 1W? I think Parameter 22 mòtor operation time setting should be ok with 240 seconds. Question: Is it the time the motor takes one move for complete moving the roller shutter in a single direction (up or down) or in both directions (up and down)? My motor takes about 26 seconds for down direction and 28 seconds for up direction. The current power is now 0.0W in idle. General questien. When the calibration starts. The shutter goes up and then is wating for 240 sec (MotorOperationTime) and then should go down- or does the roller shutter goes down immediately? My actual config looks like this. Maybe some wrong settings? UNPARSED SENSOR_MULTILEVEL 06310104220400 2017-09-15 01:11:24 assocGroup_3 Max 1 Nodes ZWDongle_0 2017-09-14 08:03:55 assocGroups 3 2017-09-15 13:21:15 configEnergyReports 10 2017-09-15 15:33:17 configInRollerBlindModeOrVenetianBlind17 10 2017-09-15 15:32:49 configInVenetianBlindModeTheParameter12 150 2017-09-15 15:32:49 configManagingLamellasInResponseTo35 SetLamellasToTheirExtreme1 2017-09-14 19:59:09 configMotorOperationDetection 10 2017-09-15 15:33:53 configMotorOperationTime 240 2017-09-15 15:33:48 configPeriodicPowerOrEnergyReports 3600 2017-09-14 19:59:09 configPowerReports 10 2017-09-15 15:52:24 configReportsType BlindPositionReportsSentToThe1 2017-09-15 15:33:32 configResponseToFloodingAlarm NoReaction 2017-09-15 15:32:56 configResponseToGeneralAlarm CloseBlind 2017-09-15 15:32:56 configResponseToSmokeCOOrCO2Alarm OpenBlind 2017-09-15 15:32:56 configResponseToTemperatureAlarm OpenBlind 2017-09-15 15:32:56 configRollerShutterOperatingModes 1RollerBlindModeWithPositioning 2017-09-15 15:32:56 configScenesAssociationsActivation AssociationsActivation 2017-09-15 15:32:56 configSelfMeasurement SelfMeasurementInactive 2017-09-14 19:59:15 configSetLamellasBackToPrevious13 1LamellasReturnToPreviouslySet1 2017-09-15 15:32:56 configSwitchType ToggleSwitches 2017-09-15 15:32:57 energy 0.07 kWh 2017-09-15 15:55:40 model FIBARO System FGRM222 Roller Shutter Controller 2 2017-09-14 07:57:09 modelConfig fibaro/fgrm222.xml 2017-09-14 07:57:09 modelId 010f-0302-1000 2017-09-14 07:57:09 position 99 2017-09-15 13:27:07 power 0.0 W 2017-09-15 15:31:18 state on 2017-09-15 13:26:47 timeToAck 0.026 2017-09-15 15:32:56 transmit OK 2017-09-15 15:32:56

And how can I see if there is a end limit switch? There must be a switch somehow because if the roller shutter is comes to its up or down endposition the S1/S2 voltage is switched off. Or what do you mean? Is there another posibility to do the calibration?

Dear community, i have the following issue with my electric roller shutters. I installed the Fibaro Roller Shutter 2 like in the manual scheme. Everything is ok. The roller shutters move up and down manualy with zwave. I use FHEM as Software. The only thing that is not working is the positioning of the roller shutters. In the manual it is described how to calibrate the fibaro module (shutters should move up, down and then up) This does not work: With the calibaration command the shutter moves up (LED is flashing green) After the shutter is in up position, the LED of the Fibaro turns flashing red but the shutter won't come down. It remain in its positon The S1, S2, Q1 and Q2 are correctly installed otherwise it would not work with software and mechanically with the toggles in the house wall. My question: Have somebody the same problem with the calibration. Any ideas. Please help!