annhan91

Yes, i changed new CMOS Pin, after, the hc2 can't autostart. I Rebooted the HC2 by power button and HC2 work OK. Voltage of old cmos pin is 1V, very low

hi, i'm using ver 4.512Beta and i think this issue board HC2. I replaced Cmos PIN -> plug power HC2 -> Turnoff HC2 by button power -> Turnon HC2 by button power and HC2 work ok. I unplug and plug power HC2 again and The HC2 work ok 1163092950314553508.mp4 The orange light of RJ45 jack turn ON -> HC2 work OK

+1 I turn off HC2 by power button and turn ON by power button then HC2 work. But disconnect Power HC2,The HC2 can't autostart. 4572190558463374008.mp4 Bios OK 922693186253804927.mp4

Hi all, My switch 2 is dead zwave. I can control by button S1,S2, but can't control by Fibaro inteface. A few months ago, All devices work well. NOW, i can't add/remote it from HC2 ( Distance between HC2 and Switch is 0.5m) The switch damaged zwave about 30 devices. Does anyone have this case? thank

POST /MediaRenderer/AVTransport/Control HTTP/1.1 HOST: 192.168.99.128:1400 Content-Length: 266 You need import HOST: IP:1400 to your virtual device and it will work

up

I can't connect the button with HC2, it'awlay tranfer fail the button work OK when i hold down the button. i tested the button with battery by wire connect -> the button work OK The face moves on top-> The button work OK

The hardware of button have issue. It can't connect to battery ? Can you check this issue ? and we can send back for you fix ?

The hardware of button have issue. It can't connect to battery ? can you check this issue ?

Hi, You can try my code local id = fibaro:getSelfId() function encode(data) local b='ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz0123456789+/'; return ((data:gsub('.', function(x) local r,b='',x:byte() for i=8,1,-1 do r=r..(b%2^i-b%2^(i-1)>0 and '1' or '0') end return r; end)..'0000'):gsub('%d%d%d?%d?%d?%d?', function(x) if (#x < 6) then return '' end local c=0 for i=1,6 do c=c+(x:sub(i,i)=='1' and 2^(6-i) or 0) end return b:sub(c+1,c+1) end)..({ '', '==', '=' })[#data%3+1]) end enter = "\r\n"; USER="admin" PASSWORD="admin123" local ip="192.168.1.31" local port=80 local tcpSocket = Net.FTcpSocket(ip,port) tcpSocket:setReadTimeout(500) tcpSocket:write("GET /ISAPI/Event/notification/alertStream HTTP/1.1" .. enter); tcpSocket:write("Authorization: Basic " .. encode(USER..":"..PASSWORD) .. enter .. enter); local nhan=tcpSocket:read() nhan=nhan .. tcpSocket:read() local tam= tcpSocket:read() tcpSocket:disconnect() local bien1=tostring(tam:match("<activePostCount>(.+)</activePostCount>")or " ") fibaro:debug(bien1)

The HC2 have error "Device notconfigured" after power loss. I can't control all devices. I restored my backup but it's still error. Can you help me? Link Video thanks

hi, My HCL have issua. I want to change backup file to another HCL. pls, help me change it? The HCL save file in store. sorry for my english. thanks

Hi, The HC2 start with USB recovery. i Can recovery but it was still broken thanks @T.Konopka , can you help me check it ? thanks

hi, my HC2 is broken. (My Picture ). It can't boot to image. Recovery -> HC2 work OK.Then, about a week later it was still broken can you help me fix it ??? thanks you for your reading

hi all, Are you interested in it ? Any ideas on what we can do with it? thanks