fhermes

Hi, it seems to be Multi channel association set with HC2 as Master Single channel associations To be set: Current (on device): Multi channel associations To be set: 1(0) Current (on device): 1(0)

Hi, i have bought two FGS-223 Modules because of there Power Measurement capacity. There are currently two devices connected. The devices change there power consumption during Use. My problem is that this does not shown in the power consumption. i should only see the power consumption if i switch it on. In Example, my lawnmover needs during charge 50W, conservation charge 2,6W and if it is driving 2,4W. If i switch the power on, the system shows me 2,6W all day, even if it is chargeching. Other Example are my pumpcontroll... it need during pumping 600W and if its in standby just 10W... . the system shows me all over day just 600W. I have changed for testing Parameter 50 = 1% , Parameter 51 = 10s , Parameter 53 = 0,01kwh but it does not change anything. Where is my fault? Does anyone should have the same issue ? Thanks in Advanced

i have just update my sensor as well, but i get an issue with Fibaro Device Template. Parameter 41 are incredible high. i have tested around and found a solution. If i disable the device template and set the parameter 41 Datatype from 1d to 4d, then i get the right value from the device back. Did you have the same issue ?

Hi, i am Using the Aeon MultiSensor for Temp and Humidity Reading. Since i have bought this sensor, i am Wondering that my rooms shows so cold, but maybe... posible thats only my feeling. But now i have build a small Test for the Temp sensor. Iam am putting the aeon MultiSensor together with Fibaro Door Sensor (+DS18B20) and the Fibaro Motion Sensor in one row. Aeon : 16,9 °C Door Sensor: 19,06°C Motion Sensor : 19,4 °C The Fibaro Sensors are more next to the real feeling. Does anyone also have similar problems with the aeon sensor ? I think this sensor or the integration in Fibaro should have a problem. I have also tested another Aeon device with same results. [ Added: 2014-12-22, 01:25 ] Nobody should have same problems ?

in my case, the configuration will be only done successful if the motion sensor are next to the HC2. If it to far away and the signal will be routed, it seems to be not working.

hi amilanov and Fibaro Team your solution seems for me like a workaround, i have test it... sometimes it works pretty well, but only sometimes in my cases. I have test a little bit more. My device in the Fibaro System should have the id16. If i send now a set value to id 17, it also glowing. Then i have try a little bit more. Set Value on id18 was only red, 19 are green and 20... you know it... Blue. I can set all colors from 0-100. 255 should not work. At this way, the devices will be glowing like i want. if i set id 10 to value 10, its only glowing low and dosent jump to 100 %. Are there any more information from Fibaro Team of the real configuration from the Fibaro RGBW device? the shown device looks for me like a virtual device.

i did not catch it. i like to set a color with a specific birgthness. fibaro:call(16, "setValue", "35"); fibaro:sleep(300); fibaro:call(16, "setColor", "80", "40", "20", "0"); with that, my rgb brithness jumps to 100% or only the white LED have to glow with 10 percent of brightness. fibaro:call(16, "setW", "25"); The only what happens is that the white string jumps to 100% could you please give me an example code how to set on the rgb_driver the right color with the brigthness that lower as 100% ? I get the same problem if i controll the driver with the webinterface. i can set a value and at first, the value jumps to 100% after that, i can move it to 20%. But if i like to move it now to 30% it jumps again to 100%

Hi, i try to use the RGBW Module in a Lua Script but i cannot set the Color. i have try it now often but it should not work. Here are my code: fibaro:call(16, "setColor", "1", "1", "1", "1"); fibaro:sleep(1*1000); test2 = fibaro:getValue(16, "color") fibaro:debug(test2); fibaro:sleep(1*1000); fibaro:call(16, "turnOff") if i send this code, the color jumps to 1,1,1,1 --- thats ok if i send fibaro:call(16, "setColor", "50", "1", "1", "1"); i get the Color 255,5,5,5 instead of expected 50,1,1,1 whats wrong there? same if i use setW, setR, setG, setB Everthing above 2 let the level of the color jump to 255.