Welcome to Smart Home Forum by FIBARO
Dear Guest,
as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.
As a member you can:
- Start new topics and reply to others
- Follow topics and users to get email updates
- Get your own profile page and make new friends
- Send personal messages
- ... and learn a lot about our system!
Regards,
Smart Home Forum by FIBARO Team
Soft
-
Posts
213 -
Joined
-
Last visited
Soft's Achievements
-
I need to replace the HC2. These days it would be smart to find a solution that will support multiple protocols when there are so many different products out there. Can I assume support for any of the ones in the title, or should I assume that Z-Wave is the only one with HC3?. I also have wall mounted iPads, and it seems that there is no iPad app currently for HC3?, when will that be available ?
-
Hi all, In the new app, the control of the Heating panel is missing the away/holyday mode selection. Is this correct or am I missing something here ? I'm trying to make it super-easy for someone to open the app, and select either one temperature to be set, indefinably until it is changed again, would prefere that. Or to be able to select a predefined temperature for away, and for home. The best would be to use the set temperature, and then that would be the temperature until you change it, without any scheduling.
-
@baskalex I forgot, the remote system I have is HCL, will not use LUA code, so not available for this setup. Any other suggestions are welcomed
-
Thanks I’ll look into that then. Kim
-
Hi all. I think I have gotten the device linking right, and that the temp sensor will control the thermostat correctly. question now is an easy way to change the desired temperature from the app. I would like to just set one temperature, no schedule or timing. Ideas? Seems that all changes I do is timed?
-
Are there any plans to make the web gui look more like the new app gui ? It is a bit old fashion ish.
-
Heatit Z-TRM2fx to be turned on/off using sensative temp sensor
Soft replied to Soft's question in Other Devices / Third-party devices
I have, but having a hard time understanding this Anyway, if I set up heating panel, how can I trigger this home and away using the app ?
-
Hi all. I'm trying to "link" this two devices, using the strip to feed the thermostat with the correct temperature. There is no way to use the internal, or external sensors in the thermostat. I'm looking for one easy button on in the app, to turn on and set temperature to 22 degrees C And one button to set the temperature to 10 degrees C, when away. All suggestions are welcome, this is HLC, device is the 60.xx range
-
Is there any ETA and screenshots of the interface?, I must be blind :-), no GUI or eta here ?...
-
I'm getting several mails every day, but cant figure out what device this is. I have only a few battery opperated devices, and have turned e-mail notification off on all. The message is just replace battery from HC2xxxxx I have nothing configured in the notification panlel, how to find out what device is sending the message ? Message comes from :- [email protected]
-
Connect temperature sensor with Heat Controller
Soft replied to Pietgeeroms's question in Heat Controller
"one notice here as far as I remember this VD use really so you should patch code and send command to thermostat with turning on heating or off instead of turnon turnoff command as relay" I'm trying to do the same thing, I have one thermometer and one on/off switch, and would like to control the on/off switch according to the given temperatur. Any good ideas how to, easily using blocks ?
-
Hi all, I have been using this with success for a long time, without any template. With the latest upgrade there is support for this lock, how do I handle this?, now the lock keeps locking and unlocking 4-8 times everytime I use Fibaro to unlock it.
-
That!, is what I never understand with Fibaro. They have a small dedicated community that actually want them to succeed, and then they totally ignore this sort of question. be frank, but most of all, show us that you care.
-
Danalock V3 Google Home Integration.
Soft replied to DefendorNL's question in Other Devices / Third-party devices
I "think" it's related to security from Googles side, you should not be able by mistake to open the lock. -
Can someone post a tutorial on how to make this work?, I do see the app on the watch, even scenes, but the ones I have selected does not show.
