Welcome to Smart Home Forum by FIBARO
Dear Guest,
as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.
As a member you can:
- Start new topics and reply to others
- Follow topics and users to get email updates
- Get your own profile page and make new friends
- Send personal messages
- ... and learn a lot about our system!
Regards,
Smart Home Forum by FIBARO Team
Search the Community
Showing results for tags 'doubleswitch'.
Found 5 results
-
Separacja zaciskow klawiszy S1/S2 od zaciskow wejsciowych O1/O2
HanSeba posted a question in Double Switch 2
Witam Pierwsze testy wykazały ze w przypadku modułu DOUBLE SWITCH 2 FGS-2x3 FGS-2x3 zawsze wyzwolenie zacisku S1 skutkuje reakcja na zacisku O1 dla S2->O2 analogicznie Oczywiście można wpływać na parametry takiego polaczenia ale nie znalazłem sposobu aby je odseparować. Za pomocą asocjacji jest możliwe bezpośrednie (bez udziału centralki) zestawienie dowolnego SX z jednego modułu z dowolnym OX z innego modułu Moim celem jest zbudowanie następującej przykładowej konfiguracji opartej na dwóch modułach DOUBLE SWITCH 2 FGS-2x3 - 4ry przyciski podłączone do wejść Sx - 4ry źródła światła podłączone do wyjść Ox - zestawienie dowolnego polaczenia pomiędzy Sx i Ox za pomocą asocjacji/scen Moim problemem jest to ze zawsze wyzwolenie Sx skutkuje reakcja w przypisanym do niego Ox (S1 zawsze wyzwala O1 a S2->O2) Proszę o pomoc w skonfigurowaniu opisanej separacja -
I am desperate and need help I’ve been trying to pair a couple of Fibaro double switches FGS-223 and roller shutter 3 using Smartthings hub actually its a full set of smartthings wifi which has a built in ST hub I’ve followed all installation instructions however i am unable to find these devices on ST app, i will be listing down all the trials i did after installation with no hope to even connect: Using Double Switch 2: 1- pressed S1 3 times but couldn’t find it. 2- pressed B button 3 times but the same. 3- reset (yellow indicator) and did the same steps but didn’t work. 4- disconnect power and reconnect and do the steps again but not working. 5- I’ve tried another 3 switches with no hope. Note: during these process I haven’t seen any flashing lights that can be indicator that I’ve entered paring mode. Using Roller shutter 3: I’ve done exact the same except I have only one device to try, also i’ve been able to see a flashing green/yellow light indictor for pairing mode. Last, I couldn’t find the fibaro in brands so i’ve been trying Z-wave generic, I’ve tried another account with a UK region where i was able to find fibaro in the brands list but couldn’t pair as well. Looking for help as i am not sure if i should go and pay extra money to get Home center hub or its another issue Thank you
-
Hi everyone! I’m quite new to the Fibaro world. In fact I’m just fiddling around with my newly bought set of equipment in my “test lab”. I can get everything to work as expected and wanted except for one thing: Associations on the fgs223 don’t seem to work at all. I tried everything: - including both a wall plug and a fgs223 non-secure - including both a wall plug and a fgs223 secure - resetting everything (including HC3) to factory defaults - setting all relevant parameters to all possible values - looking into the jsons the api provides What I can achieve is: - Associate a button of my KeyFob to a WallPlug - works charming even when the HC3 is not present. - set the association in a fgs223 for either endpoint 0 or endpoint 1 to the correct id of a WallPlug (json confirms that the association is set accordingly) Whatever I do the associations won’t trigger neither a WallPlug nor another fgs223. Is there any known issue according to associations with the fgs223? Maybe some trick to get it working? I could (and most likely will) help me out with scenes, but that’s not want I want... What am I missing? Any help or pointing into the right direction is very much appreciated! Best regards to all of you, Ben
-
Hello, my first question on this forum, so please be gentle I have Home Center 2, with some modules (roller shuters, netatmo, C02,...). I have a big trouble with buying stuff for my water control with solenoid valves, for my irrigation and water floor heating. I would like control them with double switches, so i need 6 of them for 12 valves. I found this picture on forum for control 12V Solenoid valves with the old one Fibaro Double Switch 2 FGS-221. Is this possible with the new Fibaro Double Switch 2 FGS-223 ?? I can get them here easier then the old ones. I didn't buy valves yet, so can someone tells me, what kind of them i must buy, 12/24 or 230V, DC or AC, and how i know which valves are closed when power is off. I will buy transformator from 230 to 12/24V if i must. Can someone help me with this problem? Thanks a lot for your help and your time LP Mr J.T.
-
[SOLVED]Fibaro Dimmer 2 FGD-212 - Double switch setup
pelaoboyka posted a question in Dimmer and Bypass
Hi! I purchased a FGD-212 Dimmer 2, to install it on a double switch that controls two independent lamps: Since I do not have a neutral cable in my switch box, I would like to know if I can output 'N' to 'Sx' from the FGD-212 module as indicated in the following diagram that I found on the internet: Thanks for your help.
