Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

manuelst

Question

hi,

I bought two domux products (zwave plus)) but they do not integrate correctly with fibaro hc2 release 4.120.

subsequence releases integrate dumux sensor ?

-  Domux dx1co-z  ( sensor monoxide CO)  - template id-0260-8005-1000-01-0A--.zip

-  Domux dx1cg-z ( sensor gas, CH4) – template id-0260-8003-1000-01-01-- .zip

HC2 does not detect when they are safe or breaked. On interface HC2 I always see "Never Breaked", and so my scenes don't start.

the sensors work correctly because (for example) if i use the command in lua fibaro:getValue(150, "lastBreached") i see 1518214851 that is 02/09/2018 @ 10:20pm (UTC)!!!!
that is the time when i did a test with lighter near the sensor!!! ;-)


If the sensor don't have a template it means that I can not have ony information about when it was breaked?

if i use  fibaro:get(150, 'alarmlevel')  i have always 0 both in normal conditions and when I use the lighter and I trigger the sensor that sounds. Hc2, however, does not detect anything ;-(

what is the correct command in lua to check the status and at this point make a scene
that sends me a popup or email that the sensor has detected monoxide C0?

I attach template for future integrations.
thanks best regards.

please help me!


Please login or register to see this code.

 

Please login or register to see this attachment.

Please login or register to see this attachment.

Link to comment
Share on other sites

3 answers to this question

Recommended Posts

  • 0
On 12/2/2018 at 3:46 PM, manuelst said:

hi,

I bought two domux products (zwave plus)) but they do not integrate correctly with fibaro hc2 release 4.120.

subsequence releases integrate dumux sensor ?

-  Domux dx1co-z  ( sensor monoxide CO)  - template id-0260-8005-1000-01-0A--.zip

-  Domux dx1cg-z ( sensor gas, CH4) – template id-0260-8003-1000-01-01-- .zip

HC2 does not detect when they are safe or breaked. On interface HC2 I always see "Never Breaked", and so my scenes don't start.

the sensors work correctly because (for example) if i use the command in lua fibaro:getValue(150, "lastBreached") i see 1518214851 that is 02/09/2018 @ 10:20pm (UTC)!!!!
that is the time when i did a test with lighter near the sensor!!! ;-)


If the sensor don't have a template it means that I can not have ony information about when it was breaked?

if i use  fibaro:get(150, 'alarmlevel')  i have always 0 both in normal conditions and when I use the lighter and I trigger the sensor that sounds. Hc2, however, does not detect anything ;-(

what is the correct command in lua to check the status and at this point make a scene
that sends me a popup or email that the sensor has detected monoxide C0?

I attach template for future integrations.
thanks best regards.

please help me!

 

 

Please login or register to see this code.

 

Please login or register to see this attachment.

Please login or register to see this attachment.

 

Hi Manuelst,

 

Did you have found a solution?

I have bought a Zipato HS1CG-Z (That i think is the same) but pressing the "test" buttons the params output of "alarmLevel, alarmType, lastBreached" are always "0".

Any idea?

 

 

Link to comment
Share on other sites

  • 0
  • Inquirer
  • On 22/2/2018 at 9:40 PM, Gianluca S. said:

     

    Hi Manuelst,

     

    Did you have found a solution?

    I have bought a Zipato HS1CG-Z (That i think is the same) but pressing the "test" buttons the params output of "alarmLevel, alarmType, lastBreached" are always "0".

    Any idea?

     

    ciao Gianluca,

    at the moment I did not find any solution. I have send to fibaro template. the variable lastBreaked is set but the time in linux format but the value is the time it was installed.  It would be enough to change the value of any variable to then make a scene with lua .... and I was regretted not having taken the equivalent "Zipato"... I see that the problem is the same .....

    restiamo in contatto se magari riusciamo a trovare una soluzione...basterebbe una qualunque variabile che aggiorni il valore... io con un accendino ho provato più volte a far suonare il sensore ma nessuna variabile sembra aggiornarsi e questo è strano....al di la del problema di integrazione di fibaro. presumo che sbagliamo qualcosa...tu a che conclusione sei arrivato ?

     

    Link to comment
    Share on other sites

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...