Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

Ezmotion / Homeseer 3 in 1 - 3.358 - issues


Guest shapa

Question

Guest shapa

It is not possible to add 3-in-1 in 3.358 correctly - only motion sensor is adding, device is not detected as multi_level_sensor

Image is attached

Is it known issue?

Please login or register to see this attachment.

Link to comment
Share on other sites

15 answers to this question

Recommended Posts

  • 0

Since the latest update of the ezmotion firmware wide inclusion is not working well.

Exclude and include from max 1 meter.

Link to comment
Share on other sites

  • 0
Guest shapa
  • Inquirer
  • Hi Tane,

    Thank you for the advise, but:

    1) It works fine with Vera3

    2) I've tried "1m inclusion" with exactly the same result

    3) It is always included fine but only motion sensor is detected (but small numbers on the device icon bottom left corner showing temperature or light level (!) ).

    I.e. - this is 100% Fibaro HC2 issue.

    Link to comment
    Share on other sites

    • 0

    I have the same problem.

    But in the bottom left corner I have always 0%.

    I tried to include it near HC. Tried to include with batteries and with adapter (not simultaneously). And result always the same.

    Link to comment
    Share on other sites

    • 0
    Guest Lode
  • Inquirer
  • I don't know about your experiences but i used to have that 3 in 1 sensor.

    Only troubles both with vera and Fibaro........no more for me !!!!

    Please login or register to see this image.

    /emoticons/default_icon_evil.gif" alt=":evil:" />

    Link to comment
    Share on other sites

    • 0
    Guest shapa
  • Inquirer
  • Lode,

    I do not have any issues with this sensor (which was connected earlier), and it is much faster than Aeon 4-1

    Link to comment
    Share on other sites

    • 0

    I have the same issue as shapa

    I believe the problem is with the v3.3 version of the EZMotion 3-in-1 sensor.

    The previous firmware version - v2.1 - works fine with HC2.

    Can Fibaro update HC2 to have compatibility with the v3.3 firmware EZMotion 3-in-1 sensor? It's the exact same parameter list as the previous version.

    Link to comment
    Share on other sites

    • 0

    I have the same issue

    i open a request on bugzilla

    Please login or register to see this image.

    /emoticons/default_icon_wink.gif" alt=";-)" />

    Please login or register to see this link.

    Link to comment
    Share on other sites

    • 0

    All,

    For the brief time that I had the new 3.907 beta installed I can report back that these devices were correctly listed (after a quick Re-Config). All the motion, Luz and Temps were correctly listed!

    Link to comment
    Share on other sites

    • 0

    Yes that's right 3.3

    They haven't worked very well with the 3.x version. However, I can report that for the short time I had THE 4.x new binary loaded once I did a reconfigure they behaved much better.

    Link to comment
    Share on other sites

    • 0

    That is good news indeed! Anybody else tried these on the new 4.x and can confirm that motion, lux and temperature works ok?

    [ Added: 2014-09-29, 07:46 ]

    Hmmm, just noticed that these have been discontinued a couple of weeks ago and all big dealers seem to be out of stock. It's a shame really, they were the only 'normal' looking movement sensors along with the Vision. But the latter seems to be much less advanced in terms of adjusting settings.

    Link to comment
    Share on other sites

    • 0

    Still facing issue's with the Ezmotion 3-1 , no motion , no Temp detection or lux measurement.

    Only the first time when the sensor is included.

    Is their any solution for adding / using this sensor on a "normal" way ?

    many thanks

    Marco

    Link to comment
    Share on other sites

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...