Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

Alarm Message from Temperature


Berges01

Question

Hi there

I use the binary universal for temperature measurements and pressure as well as a flood report.
IN1 pressure> 2 bar with a pressure switch
IN2 flooding with a water level detector
Temperature 1 heating flow
Temperature 2 heating return
Temperature 3 hot water heating flow
Temperature 3 hot water heating return
So far everything is OK.
Every now and then I get an alarm message from temperature 1.
I guess every time the temperature of the sensor rises above 60 ° C.
Does anyone have an idea how to turn it off?
My gateway is an HC3
Greetings from Germany / Sauerland

Link to comment
Share on other sites

4 answers to this question

Recommended Posts

  • 0

hi you should change the temperature above 60°C in the general panel. You can't switch this option off AFAIK, or you should change your default temperature sensor to another one.

 

 

Edited by Tony270570
Link to comment
Share on other sites

  • 0
  • Inquirer
  • Hi there

    Where should I change the temperature above 60 ° C?
    Do you write in the general part?
    Nothing works at the moment.
    The system (HC3) is still very unstable and I am currently struggling with the pitfalls of the system.
    This morning I still had 40 sensors running including all the trimmings.
    The mash became stable and tonight a backub did not start.
    Everything I did today (16 sensors and some program parts etc.) gone!
    Restore backup is also not possible, the system does not start up.
    I still have to try to back up yesterday.
    At the moment I am fustrated I have about 90 different sensors and actuators that ran on my old system (homee).
    But I want to have analog sensors and more functions when programming and so I try my luck with HC3.
    Back to the problem, there was no such thing with the message at homee, so it has to be switched off just how? The manual gives no information. Maybe that comes from the HC3 but I have not yet identified all the buttons and much is still new!
    So keep looking and blocking mail.

    Link to comment
    Share on other sites

    • 0

    hi, and keep cool, next firmware is coming ;)

    Please login or register to see this attachment.

    Edited by Tony270570
    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • Great thank you !!
    I had already seen that but could not assign it!
    I dumhead but everyone starts over.
    Not everything went smoothly at home and I suspected that there could be problems with a new system.
    But as the saying goes, "hope dies last"?
    I hope there is such a saying in France
    I have set the factory settings and I restart!?
    Let's see if I can go on.
    The system has stopped and it is no longer possible to restore a backup.?

    Link to comment
    Share on other sites

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...