Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

Swap output logic


suchy

Question

Hello

Well, I have problem: I change parameters 155 and 156 responsible for the logic of output 1 and 2, and yet I always have the default state at the outputs: "normally open / closed active state" - nothing has changed... Did any of you have such a problem? I have not noticed any other settings related to these parameters that would block these settings.

 

Suchy

Link to comment
Share on other sites

7 answers to this question

Recommended Posts

  • 0

Just one question. Did you have disconnected inputs and outputs during your experiments? ..

eM.

Link to comment
Share on other sites

  • 0
On 1/30/2021 at 9:44 AM, suchy said:

Hello

Well, I have problem: I change parameters 155 and 156 responsible for the logic of output 1 and 2, and yet I always have the default state at the outputs: "normally open / closed active state" - nothing has changed... Did any of you have such a problem? I have not noticed any other settings related to these parameters that would block these settings.

 

Suchy

 

@suchy

@

Please login or register to see this link.

@suchy

 

 

Hello.
I already told you in the first post ...
From my experiments with Smart Implant, I came to the conclusion that it behaves "strangely", but it is possible to work with it.

I enclose a picture that will guide you through the necessary steps.

1) turn off protection (input-output link)
2) change the input definition
3) undo protection (input-output binding)
4) change the definition of logical operation (154)

This setting will provide you with a variant:
IN1 = OFF (log 0) => BI1 (move sensor - stick figure = OFF [stay]) => OUT1 = ON (log 1)
IN1 = ON (lof 1) => BI1 (move sensor = ON [goes]) => OUT1 = OFF (log 0)

 

Please login or register to see this spoiler.

 

 

Another variant for control - reverse
Set the input configuration (step 2.) to "Binary input NC".
Change parameter 154 (154 = Set: 1).
This setting will provide you with a variant:
IN1 = OFF (log 0) => BI1 (move sensor = ON [goes]) => OUT1 = ON (log 1)
IN1 = ON (lof 1) => BI1 (move sensor - stick figure = OFF [stay]) => OUT1 = OFF (log 0)

 

The last variant for control - reverse for the BI state.
Set the input configuration (step 2.) to "Binary input NC".
Do not change parameter 154 (154 = Set: 0).
This setting will provide you with a variant:
IN1 = OFF (log 0) => BI1 (move sensor = ON [goes]) => OUT1 = OFF (log 0)
IN1 = ON (lof 1) => BI1 (move sensor - stick figure = OFF [stay]) => OUT1 = ON (log 1)


Important thing.
After setting, you need to change the state of the input several times ... then it will work as expected.

 

eM.

 

Edited by Martin_N
Link to comment
Share on other sites

  • 0

@suchy

... this post doesn't mean anything ... it just doesn't work correctly to enter my nickname for notification ...

eM.

Link to comment
Share on other sites

  • 0

@A.Socha and @m.roszak:

Changing Output logic with the parameters 154, 155 of the Smart Implant fails for a long time using HC3.

When will this be repaired?

Link to comment
Share on other sites

  • 0

@RoverSorry but I don't understand what your problem is. Do you not know how to set the parameters on HC3?

Link to comment
Share on other sites

  • 0
8 hours ago, A.Socha said:

@RoverSorry but I don't understand what your problem is. Do you not know how to set the parameters on HC3?

The problem is that changing the parameters 154 or 155 of the smart implant has no effect! It behaves in NO as well as NC setting always as NO.

Link to comment
Share on other sites

  • 0

@Rover

Have you read this fiber carefully and especially my post ???

The fact that SI behaves "strangely" is possible, but I wrote a procedure to get the result. Give it a try and report it.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...