Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

Usuwanie urządzeń z HC3


marekneo

Question

Cześć. Jak usunąć urządzenie z HC3? Jedno z urządzeń mi padło, nie reaguje na nic. Chcę je usunąć z centrali a nie mogę tego zrobić poprzez wybudzenie gdyż jest uszkodzone. Jak alternatywnie, bez wybudzania można usunąć urządzenie z centrali HC3? Niestety nie mogę tego znaleźć.

Z góry dziękuję za pomoc.

Link to comment
Share on other sites

10 answers to this question

Recommended Posts

  • 1

rozpocznij jak zawsze ...

 

Please login or register to see this attachment.

 

Please login or register to see this image.

/monthly_2021_10/image.png.d879c790d1a7fda659ff40f0075a2b16.png" />

 

 

i terat mozesz nacisnac na ten znak

 

Please login or register to see this attachment.

 

i potwierdzic

 

image.png.4180f96938ca7283fbd5cbdcecd941f2.png

 

Teraz tylko odczekaj, albo zniknie i jest usuniete, albo bedzie blad (np. nadal osigalne, wiec musi byc wybudzone, itd)

 

 

 

 

  • Like 2
Link to comment
Share on other sites

  • 0
W dniu 1.10.2021 o 12:52, tinman napisał:

rozpocznij jak zawsze ...

 

Please login or register to see this attachment.

 

Please login or register to see this link.

 

 

i terat mozesz nacisnac na ten znak

 

Please login or register to see this attachment.

 

i potwierdzic

 

Please login or register to see this link.

 

Teraz tylko odczekaj, albo zniknie i jest usuniete, albo bedzie blad (np. nadal osigalne, wiec musi byc wybudzone, itd)

 

 

 

 

Dziękuję. Mi również pomogło. Miałem problem z głowicą Danfoss.

 

Link to comment
Share on other sites

  • 0

Trafiłem na info:

Please login or register to see this link.

ale ja nigdzie nie widzę przycisku "Wymuś usunęcie"

Czy ktoś ma jakiś pomysł? Co robię źle?

Link to comment
Share on other sites

  • 0

Ja klikam KOSZ przy urządzeniu i Wymuś usunięcie. Ostatnio Nadrzędne urządzenie wywaliło a przyciski zostały - BŁĄD. Pomaga restart centrali znikają i przyciski :-)

 

image.png.4d92c7fb318210b29a3fd0a063771e00.png

Link to comment
Share on other sites

  • 0

Ja cały czas mam problem z WallPlugiem, który "odpiął się" od Centralki. Próbowałem zrobić rekonfigurację - bezskutecznie. Skonfigurowałem na nowo urządzenie, ale próba wymuszenia usunięcia starego nie działa. Mimo, że próbuję wymusić usunięcie urządzenia o ID:23 (to "odpięte"), centralka zgłasza błąd na id:689. : [ZWAVE]: ID 689: NOP sending succeeded. The device has not been removed. Please use Learning Mode to remove it. Dodatkowo ta rekonfiguracja starego cały czas trwa od 2 mscy (mimo resetów) i blokuje rekonfigurację innych urządzeń. Opisałem to tutaj.

Please login or register to see this link.

. Czy to jest temat do serwisu?

Link to comment
Share on other sites

  • 0

Mi wyskakuje jedynie takie okienko

Please login or register to see this image.

/monthly_2023_10/image.png.3a1624a635f1488dbeaed2f346b22d44.png" />

Link to comment
Share on other sites

  • 0

Problem rozwiązany, miałem stary firmware w HC3.

W najnowszej wersji wyskakuje okienko:

Please login or register to see this image.

/monthly_2023_10/image.png.772911aeb53b636f824d852d12c3bbe1.png" />

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...