Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

The damn thing keeps disconecting ;/


ppeterr

Question

I've been putting a multi sensor into use for weeks now. Can't seem to get that thing stable. As simple as it should be, it doesn't work.

One time it stays connected for a week, the next time the connection is gone a day later. Just a little while and I'll swing that nice ball over the hedge :P But maybe I'm doing something wrong, and do you have a good tip? I have set the wake-up time to 4000s, only set parameters 40 and 42 different. The rest is standard.

 

 

Please login or register to see this attachment.

Please login or register to see this attachment.

Link to comment
Share on other sites

Recommended Posts

  • 0
  • Inquirer
  • 2 minutes ago, akatar said:

    @ppeterr

    http://192.168.1.36/api/service/logsDump

     

     

    Thanks that works, got some dump file now. This is after the zwave service restart.

    I'll get one next time also when it is disconnected.

     

    thanks guys.

    • Like 1
    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • Thats funny, 4 days later - again the same problem.

     

    Made the logs, before i did the trick to reconnect. So, now i have logs before, and after.

     

    Link to comment
    Share on other sites

    • 0
    4 hours ago, ppeterr said:

    There is a pattern :)   4 days later. Again disconnect.

    Stable is ok.

    [trollface]

    • Like 1
    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • 27 minutes ago, akatar said:

    Did you sent the logs to fibaro support?

     

    This is not urgent :) 

     

    Or at least, not for now. And i think Mr Roszak is on it also...

     

    So, if they need the logs, i will provide. 

     

    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • Oehhhh, what should i do......

     

    I updated to 5.092.19. Amd that went smooth.

    But now there is another....

     

     

    Oehh....this might be good :)

     

     

     

     

    Please login or register to see this attachment.

    Edited by ppeterr
    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • Yesterday i did the 5.092.19 update. So far so good.

    Today, the connection with the sensor was lost, and the zwave -> smart start -> firmware upgrade tabs, crashed.

    Or, i think it crashed the whole zwave 3 service/protocol. After a reboot it all worked again.

     

    Then,  i performed the device update for the sensor, from 3.3 to 3.4

    This went oke..or at least, the version number stays on 3.3 after a succesfull update.

     

    @m.roszak

     

    I'm not sure now if the update went through. The option to update is gone. And the version is still 3.3

     

     

    Link to comment
    Share on other sites

    • 0
    10 minutes ago, ppeterr said:

    Yesterday i did the 5.092.19 update. So far so good.

    Today, the connection with the sensor was lost, and the zwave -> smart start -> firmware upgrade tabs, crashed.

    Or, i think it crashed the whole zwave 3 service/protocol. After a reboot it all worked again.

     

    Then,  i performed the device update for the sensor, from 3.3 to 3.4

    This went oke..or at least, the version number stays on 3.3 after a succesfull update.

     

    @m.roszak

     

    I'm not sure now if the update went through. The option to update is gone. And the version is still 3.3

     

     


    try soft reconfigure or reconfigure and check the version again 

    • Like 1
    Link to comment
    Share on other sites

    • 0

    There is a notification in panel that device need to be reconfigured after successful update :)

    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • On 12/24/2021 at 6:25 AM, ppeterr said:

    Thanks guys, that worked :)

     

    Well.......one day later..disconnected

     

    - zwave protocol error

    - 502 gateway error


    And it's reconnected.

     

    I must be doiing something wrong :) I dont see any other user having this problem

    having  the zwave engine crash on their system. Or am i wrong ?

     

     

    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • I have submitted a case to the support department. With some logs.

     

    Edited by ppeterr
    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • @m.roszak

     

    Something seems to have changed, for now it looks good.

     

    Not sure why, not sure how. But the damn thing keeps connected :)

    • Like 1
    Link to comment
    Share on other sites

    • 0

    We have changes some things in backend for ZW3.0 in 5.100 - maybe that is why.
    As we did not reproduce this one it is a mystery :)

    • Like 1
    Link to comment
    Share on other sites

    • 0
    12 hours ago, m.roszak said:

    We have changes some things in backend for ZW3.0 in 5.100

     

    hijacking topic a bit, but indeed that helped in my case with 3rd part sensor (700 series based) disconnecting all the time, on HC3 with zw3. Since 5.100 no issues since 7 days.

    • Like 1
    Link to comment
    Share on other sites

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...