Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

Light sensor not showing on Home Center 3 Light with the Z-Wave 3.0 engine


talofer99

Question

Currently testing a wall mounted switch, with 4 relay and buttons.
The device has a light sensor as well.

On none secure controllers we will get an "end point" of sensor, for example this is how it looks on the Fibaro Lite

Please login or register to see this image.

/monthly_2022_08/1.jpg.176f57edaf57acfe62852e77c450df34.jpg" />

 

 

And looking on the unsolicited update frame that is been sent the data is ok and the interface gets updated.
2.jpg.3493d7c8f5ffb10298c6d2d933a3141c.jpg

 

 

Now on the new Fibaro Home Center 3 Lite, with the  Z-wave 3.0 engine in S2 , this is how the interface looks at the end of the join process
3.jpg.97796b04ff46a45ab59fe3e880eec4e7.jpg

 

 

 

Unfortunately I do not have access to the Keys on this fibaro (If you know how to gain them let me know), 
but when I tested all the frames that are available for this class it all worked and response well.

 

Any ideas, suggestions, need for more info will be highly appreciated. 


 

 

 

Link to comment
Share on other sites

Recommended Posts

  • 0
  • Inquirer
  • @m.roszakthank you very much for the information. 
    I will look into the % vs lux in the documentation and adjust the code. 
    This product is not yet in the market. 

    Again thank you, and I will report back if I worked it out. 
     

    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • @m.roszakI finally got to test this out  - we were busy with other parts of the project. 
    I check the setting and indeed they were incorrect and instead of the value being 0x04 (0x01 on Bit 2) it was 0x01. 
    I got this value from this table 

    Please login or register to see this attachment.

     

     

     

    Now I adjusted the code and tried to join the fibaro and still I do not see the sensor. 


    I check the output of each of the Class command and as far as I can tell they are fine. 

    This is the supported Sensors

    Please login or register to see this attachment.

     

     

    This the fixed supported sensor scale 

    Please login or register to see this attachment.

     

     

    And this is the sensor report 

    Please login or register to see this attachment.



    Is there something I'm still setting incorrectly ? 
    If not, can I send you a log from the Fibaro again to see why I do not see the Sensor ? 


    Again thank you for all the help. its highly appreciated

    Tal 



     

     

    Link to comment
    Share on other sites

    • 0
  • Inquirer
  • @m.roszakthank you very much for the help :) 


    Attached is the log, I also first upgraded the device to the latest version 

    Please login or register to see this attachment.

    Link to comment
    Share on other sites

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...