Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,


as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.


As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!



Smart Home Forum by FIBARO Team

Search the Community

Showing results for tags 'fgbs321'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • FIBARO Community
    • FIBARO Portal and Forum policy
    • FIBARO
    • Say hello!
    • Off-topics
  • FIBARO Update
    • FIBARO System Update
    • FIBARO Mobile Update
  • FIBARO Community Support
    • Scenes and Interface
    • FIBARO Products
    • FIBARO Mobile
    • FIBARO HomeKit
    • FIBARO Assistant Integrations
    • Other Devices / Third-party devices
    • Tutorials and Guides
    • Home Automation
    • Suggestions
  • FIBARO Społeczność
    • FIBARO
    • Przywitaj się!
    • Off-topic
  • FIBARO Aktualizacja
    • FIBARO System Aktualizacja
    • FIBARO Mobile Aktualizacja
  • FIBARO Wsparcie Społeczności
    • Sceny i Interfejs
    • FIBARO Urządzenia
    • FIBARO Mobilnie
    • FIBARO HomeKit
    • Integracja z Amazon Alexa i Google Home
    • Urządzenia Firm Trzecich
    • Poradniki
    • Automatyka Domowa
    • Sugestie


  • Scenes
  • Virtual Devices
  • Quick Apps
  • Icons

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start






Website URL





Found 1 result

  1. Hi, I'm hoping that somebody can help me. HC2 - v 4.056. 40-50 devices, reasonably familiar with the system I have been working with the universal binary sensor for a while now and have a few of them working with temp sensors and contact sensors. I upgraded to 4.056 when it was released and haven't touched that side since. I bought some more UBS in the last few weeks to gather more temperature readings and to enable a more contact sensor and I've ran into an issue. When I add a new device it appears as a generic z wave device with no parameters and I can see from the inclusion process that its not going well. On inclusion I get one device that is not configured When I include the device I get [21:54:31] Device added [21:54:43] Add node status protocol done [21:54:43] Adding devices complete The add device page stays open and I have to close ( I have left it for 10 mins at this stage) The learn mode led on the HC2 blinks as it is being added. The zwave led (fourth led) on the HC seems to be permanently blinking, maybe this has always been the same but I never noticed it before. On inclusion the advanced tab shows..... Device kind: Z-Wave device Version: Configuration: Not configured ID: 93 Configuration The device does not have a template by what might have limited functionality, please contact technical support in order to add the template for this device. On excluding/deleting the device I get [22:36:12] Home Center in learning mode [22:36:18] Device was deleted succesfully [22:36:18] ID 933: Deleting devices succesful [22:36:19] Slave Device Detected [22:36:19] ID 933: Controller was deleted succesfully [22:36:19] Removing devices finished I have read through the forum and tried all that I could find and a few more. Most of what's below I have tried several times at least but no luck reset device hard reset and ffw reset (holding the button down for 10 seconds while powering off and on the device) Tried different power supplies soft reconfigure tried a new UBS that was never added before as well as two that I had added successfully in the past. rebooted the HC2 check the diagnostics panel for CPU, RAM, etc resources excluded and included a good many times tried the device with nothing connected to it, a contact sensor connected and a device with 4 temp sensors connected moved the device to be within a foot of the HC2 during inclusion tried network wide inclusion I had added a SPC Gateway (great bit of kit from Goran) device to interface with my alarm and I removed this and disabled the scenes that were associated - a reboot of the HC2 did nothing The only other big thing I did lately was to add VD for my 14 sonos zones (including all the variables) but I cant see how that would be impacting the device inclusion process These devices used to add in a minute or less and I have left some of these for 10 mins and more, The only thing I haven't tried is excluding one of my working ones and seeing if it will include again. I might try that tomorrow night if I can get to when I installed it. I don't want to upgrade to the latest beta as there seems to be some challenges and I have dimmers and switches buried in walls and I can have them go down on me at the moment. Any and all suggestions and perspectives welcome... hopefully somebody can help me solve this one Thanks -F
  • Create New...