SCENE WITH DOOR/WINDOW SENSOR

[tomek88zg 0]

Hi!

I have purchased Danffos Live termostat and i associated him in HC2.

i would like to make one scene for automatic management for heating.

My door/window sensor is eqiupped with DS - 001 temperature sensor.

i would like to open heating when temperature is drop to 18 C and shut it down when temperature is 24 C.

what i need is codes for LUA scene? how i can write the code that fibaro read the current temperature and open the heat when is 18 C and shut it down when is 24 C

i'm newbie in LUA programing

thanks a lot in advance

[A.Socha 133]

tomek88zg, you can use heating panel but by scene you can do that too in lua

[DynaRy 0]

Why don't you use the heating panel?

You can assign different rooms / zones with their individual temp. settings and working hours.

Under the linked device panel you can add your thermostat and relay to work together to turn your heating device on or of (in relation to the temp. settings in Heating Panel)

Regards,

[wasil 0]

Why don't you use the heating panel?

You can assign different rooms / zones with their individual temp. settings and working hours.

Under the linked device panel you can add your thermostat and relay to work together to turn your heating device on or of (in relation to the temp. settings in Heating Panel)

Regards,

How is that possible to link Danfoss thermostat with dallas temp. sensor?

[DynaRy 0]

Why don't you use the heating panel?

You can assign different rooms / zones with their individual temp. settings and working hours.

Under the linked device panel you can add your thermostat and relay to work together to turn your heating device on or of (in relation to the temp. settings in Heating Panel)

Regards,

How is that possible to link Danfoss thermostat with dallas temp. sensor?

Not with the Danfoss valves them self, but à relay to switch your boiler on/off. Your Danfoss valves get their parameters set by the settings you made in the heating panel.

The linking between the relay and the temp. sensor is done in the device linking panel (paperclip symbol). Under HEATING, you link the devices to the room/section where your temp sensor is.

When the temperture monitored drops below the predefined setting, HC2 sends signal to relay to fire up your boiler (gas or electric). The Danfoss valves wil shut off by them selves when the predefined temp is reached (thermostatic valve) As the Danfoss valves dont have an readable temp sensor in HC2 (only available with their own system, due to closed source protocol).

You need à separate temp. Sensor which monitors your room temp. if it reaches the predefined temp. HC2 shuts off your boiler with the relay.(according to the temp. Shedule, you defined in the heating panel. The Danfoss thermostats take over these settings only if you added them to the room/section.

Succes

[wasil 0]

Not with the Danfoss valves them self, but à relay to switch your boiler on/off. Your Danfoss valves get their parameters set by the settings you made in the heating panel.

The linking between the relay and the temp. sensor is done in the device linking panel (paperclip symbol). Under HEATING, you link the devices to the room/section where your temp sensor is.

When the temperture monitored drops below the predefined setting, HC2 sends signal to relay to fire up your boiler (gas or electric). The Danfoss valves wil shut off by them selves when the predefined temp is reached (thermostatic valve) As the Danfoss valves dont have an readable temp sensor in HC2 (only available with their own system, due to closed source protocol).

You need à separate temp. Sensor which monitors your room temp. if it reaches the predefined temp. HC2 shuts off your boiler with the relay.(according to the temp. Shedule, you defined in the heating panel. The Danfoss thermostats take over these settings only if you added them to the room/section.

Succes

I know how to do that, but tomek88zg, wanted to use Dallas temp. sensor with Danfoss thermostat and You are writing about relay switch

Please login or register to see this image.

/emoticons/default_icon_razz.gif" alt=":-P" />

To sum up, if You have Danfoss Thermostate You do not need to buy additional temp. sensor. If You want to take control of Your gas/electric boiler You can use relay switch which CAN BE linked with Dallas temp. sensor

Please login or register to see this image.

/emoticons/default_icon_wink.gif" alt=";-)" />

[tomek88zg 0]

thanks guys

i have trouble with how to associate a zone, but i find it and everything works fine

Please login or register to see this image.

/emoticons/default_smile.png" alt=":)" srcset="https://forum.fibaro.com/uploads/emoticons/[email protected] 2x" width="20" height="20" />