duwi everlux z-wave.me

[SilverApe 0]

Hi all,

I have a duwi everlux z-wave.me switch and I want to include it with my HC2 but it does not work properly. Does anyone have any experience with this switch?.

When I try to include it I get the following message: Learning mode error. Try again. (see screenshot).

Then I see the device but it is not configured (see next screenshot).

I tried reconfiguring the device but no luck.

Any help is welcome.

Greetings,

Aaron

Please login or register to see this attachment.

Please login or register to see this attachment.

[Quikdav 15]

Hi all,

I have a duwi everlux z-wave.me switch and I want to include it with my HC2 but it does not work properly. Does anyone have any experience with this switch?.

When I try to include it I get the following message: Learning mode error. Try again. (see screenshot).

Then I see the device but it is not configured (see next screenshot).

I tried reconfiguring the device but no luck.

Any help is welcome.

Greetings,

Aaron

Hi SilverApe

Which model do you have excatly ?

I have the model 06443 and I added it without any issue...

But my model doesn't send any report to the HC2 !!!

I know when I use it only because I associated it to a FGS221. And the FGS221 send it status to the HC2, it is the only way I found to know the status of this device !!!

Regards

David

[SilverApe 0]

Hi David,

Sorry for this very late reaction.

I have added a picture of mine. HC2 now says it is configured (after a couple of days) but I am still missing some options.

If I am right you are able to control two devices with it? One wit 1 click an the other with 2 clicks. How do you define that?

greetings,

Aaron.

[ Added: 2013-09-06, 18:59 ]

Hmmm now again not configured and a sending error and a transfer failed (see image)

Please login or register to see this attachment.

Please login or register to see this attachment.

Please login or register to see this attachment.

[Mitam 0]

Hi all,

I have same problem.

When I try to include it I also get learning mode error message.

My switch is model 05443.

Does anyone know what switch would work with HC2?

Regards

Mitam

[SilverApe 0]

Maybe it is the HC2 software version? I have 3.560 beta

[Quikdav 15]

Hi David,

Sorry for this very late reaction.

I have added a picture of mine. HC2 now says it is configured (after a couple of days) but I am still missing some options.

If I am right you are able to control two devices with it? One wit 1 click an the other with 2 clicks. How do you define that?

greetings,

Aaron.

[ Added: 2013-09-06, 18:59 ]

Hmmm now again not configured and a sending error and a transfer failed (see image)

My model is 6443....

Normally, you should have the procedure for association with your packaging. Else here is the procedure I used to associate my DUWI to a FGS221

Associations can be assigned and remove either via Z-Wave commands or

using the controller itself.

1. Triple click “Association” button.

2. Triple click “Inclusion” for assigning an association or “Exclusion” for

removing an association.

3. Single or double click the DOWN or UP Button to device which

association the target device shall be associated to (single click group

or double click group)

4. Issue a Node Information Frame from the target device. This is

usually done by single or triple click a button. Please refer to the

manual of this device how to issue a NIF.

I didn't try with the double click but it works well with single click. I will buy an other DUWI and I will try the association on the same FGS221

Let me know if it works for you....

David

[nkv 0]

My model is 6443....

Normally, you should have the procedure for association with your packaging. Else here is the procedure I used to associate my DUWI to a FGS221

David

Hi, everybody.

I have devices that you are talking about - HC2, Z-Wave.Me 06443 and FGS221 2x1.5.

I can easily associate 06443 (both single and double clicks) with primary device of FGS221, but not with SLAVE.

Could anybody tell me a way how to associate 06443 with a SLAVE device of FGS221? Or how to request NIF from FGS221 slave device?

[j.nowacki 5]

nkv, slave device cannot be associated to another module, please use scene or virtual device to achieve the same goal.

[nkv 0]

nkv, slave device cannot be associated to another module, please use scene or virtual device to achieve the same goal.

Ok. Thank you. I'll do this way.

One more question.

From 06443 specification I know that 06443 supports Association V2 and Multi Channel Association V2. Does that means that FGS211 2x1.5 is not multichannel capable device or does not support this kind of association?

At the same time I've found the page (

Please login or register to see this link.

) where one FGS211 is directly associated to S2 of another FGS211 (that is multichannel device node according to the link). Looks like it is just a lack of support for 06443 on the HC2 side.