Problem with my scene.

[Alex280181 0]

Hi,

 

i have a scene to control my blinds, it basically does what it should do, the only problem i face is, that it starts more than just once.

I would like to abort the scene if it was started before and its not finished, means the blades of blinds are back to 100.

 

--[[

%% properties

12 value

10 value

26 value

30 value

34 value

24 value

32 value

28 value

38 value

12 sceneActivation

10 sceneActivation

26 sceneActivation

30 sceneActivation

34 sceneActivation

24 sceneActivation

32 sceneActivation

28 sceneActivation

38 sceneActivation

3 WeatherConditionConverted

%% globals

Tageszeit

--]]

 

local startSource = fibaro:getSourceTrigger();

if fibaro:countScenes() > 1 then fibaro:abort() end

if (

 ( fibaro:getGlobalValue("Tageszeit") == "Sunrise"  and  fibaro:getValue(3, "WeatherConditionConverted") == "clear"  and  tonumber(fibaro:getValue(12, "value")) <= 10  and  tonumber(fibaro:getValue(10, "value")) <= 10  and  tonumber(fibaro:getValue(26, "value")) <= 10  and  tonumber(fibaro:getValue(30, "value")) <= 10  and  tonumber(fibaro:getValue(34, "value")) <= 10  and  tonumber(fibaro:getValue(24, "value")) <= 10  and  tonumber(fibaro:getValue(32, "value")) <= 10  and  tonumber(fibaro:getValue(28, "value")) <= 10  and  tonumber(fibaro:getValue(38, "value")) <= 10)

or

startSource["type"] == "other"

)   

then

fibaro:call(12, "setValue2", "0");

fibaro:call(10, "setValue2", "0");

fibaro:call(26, "setValue2", "0");

fibaro:call(30, "setValue2", "0");

fibaro:call(34, "setValue2", "0");

fibaro:call(24, "setValue2", "0");

fibaro:call(32, "setValue2", "0");

fibaro:call(28, "setValue2", "0");

fibaro:call(38, "setValue2", "0");

fibaro:call(12, "setValue2", "50");

fibaro:call(10, "setValue2", "50");

fibaro:call(26, "setValue2", "50");

fibaro:call(30, "setValue2", "50");

fibaro:call(34, "setValue2", "50");

fibaro:call(24, "setValue2", "50");

fibaro:call(32, "setValue2", "50");

fibaro:call(28, "setValue2", "50");

fibaro:call(38, "setValue2", "50");

  elseif ( fibaro:getGlobalValue("Tageszeit") == "Sunrise" and (fibaro:getValue(3, "WeatherConditionConverted")) ~= "clear")

then 

    fibaro:call(12, "setValue2", "100");

fibaro:call(10, "setValue2", "100");

fibaro:call(26, "setValue2", "100");

fibaro:call(30, "setValue2", "100");

fibaro:call(34, "setValue2", "100");

fibaro:call(24, "setValue2", "100");

fibaro:call(32, "setValue2", "100");

fibaro:call(28, "setValue2", "100");

fibaro:call(38, "setValue2", "100");

end

 

any idea

[rajp 14]

Not too good on Lua but if the scene is starting again and again, I would try and check if the Scene is enabled just when you check the scene count using

 

fibaro:isSceneEnabled.

 

May be set it to disabled using

 

fibaro:setSceneEnabled(x, false)

 

and then at the end set it to true. That may get around this issue.

[alex88 71]

What do you mean it is starting more than once? Do you mean that when a single trigger happens that more than one scene starts?

 

If you are on version 4.040 then there is a bug where scene activation on dimmers results in two scenes starting instead of one.

 

If  this is the case then change "if fibaro:countScenes() > 1 then fibaro:abort() end" to "if fibaro:countScenes() > 2 then fibaro:abort() end"

[Alex280181 0]

it starts automatically as soon as all values are fulfilled, the problem i have it starts over and over again. i want it to start as soon as its sunny to lower the blinds and than stop until its cloudy again.

so far it starts every 2 - 3 minutes lowering the blinds again even though i put the scene count