Heating setpoint time between 2 setpoints

[Jaapkooi 1]

Hello

I have a problem with the new heating panel . in the old heating panel the time between two setpoins was at least one minute apart, in the new it's one hour.

Question  Can this be changed.

 

reason .  I used to make 2 zone's   living morning ,living evening .     in the morn ing  time 5:30 Temp 21C   then at 5:31 temp Nil  then

 

at 8:00  temp 17C   and 8:01  Temp Nil   . one zone full.

Nou in the time between 5:31 and 8:00   and 8:01  til lets say 15:00  Ican ajust temp on my phone and thermostat and the HC2 wond interfere with it  .

[I.Srodka 4]

Hi, @Jaapkooi!

 

Welcome to our community!

1 hour ago, Jaapkooi said:

I have a problem with the new heating panel . in the old heating panel the time between two setpoins was at least one minute apart, in the new it's one hour.

This change has a logical explanation. Instead of setting some "minute after minute" set points, you can just leave one set point at 8. This solution, however, does not include your second solution which is not exactly clear to me:

 

2 hours ago, Jaapkooi said:

at 8:00  temp 17C   and 8:01  Temp Nil   . one zone full.

Nou in the time between 5:31 and 8:00   and 8:01  til lets say 15:00  Ican ajust temp on my phone and thermostat and the HC2 wond interfere with it  .

 

Could you elaborate on that?

[Jaapkooi 1]

Hi 

What I ment if you set it time 8:00 temp 21C in my Heating paneel than if I  set my thermostat at 8:15 to 22c my HC2 wil put it back to 21C at next pol  .

Not when you set it at nil at 8:01.

 

 

Edited October 23, 2017 by Jaapkooi

[I.Srodka 4]

Hi @Jaapkooi,

 

Why would you want to set another range, from 8:01 when the last one ends at 8, it means the next starts at 8:01 automatically.

 

I think I know what you mean, but this could be executed, setting "morning" mark to, for example, 7:15, then next setpoint at 8:15, and in this range from 8:15 you can set NONE:

Please login or register to see this attachment.

 

[Jaapkooi 1]

39 minutes ago, I.Srodka said:

Hi @Jaapkooi,

 

Why would you want to set another range, from 8:01 when the last one ends at 8, it means the next starts at 8:01 automatically.

 

I think I know what you mean, but this could be executed, setting "morning" mark to, for example, 7:15, then next setpoint at 8:15, and in this range from 8:15 you can set NONE:

Please login or register to see this attachment.

 

Hi good morning.

Yes that's what i mean for one temp setting you two setpoints  and nou you can change te temp on the thermostat  between 7;15 and +- 18:00 .

you have one overlap at 7:15 to 8:15 that the HC2 wil put it at 20.5C if you would change temp on your thermostat.

For the rest of the day if you change temp om your thermostat  ( 18:00 to 7:15 )  wont work ,you would have to do it with manuel mode.

 

thank's

Please login or register to see this attachment.

Please login or register to see this attachment.

[I.Srodka 4]

@Jaapkooi,

 

I do not have an overlap from 7:15 to 8:15, I just have consecutive set points set up.

 

But... that was your idea/suggestion/ask to be able to set temperature from 8:15. If the set points cannot be set in shorter time span than one hour, I just set one to 7:15 which is irrelevant, and the second one to the final hour from which we would like to be able to control it via thermostat.

17 hours ago, Jaapkooi said:

than if I  set my thermostat at 8:15 to 22c

 

Finally, could we start from the very beginning and could you write, what exactly would you like to accomplish? I think that there is some misunderstanding between us in the matter how Heating Panel works. So could you write, what do you want to do with this schedule and what is not possible? 

[Jaapkooi 1]

22 minutes ago, I.Srodka said:

@Jaapkooi,

 

I do not have an overlap from 7:15 to 8:15, I just have consecutive set points set up.

 

 

But... that was your idea/suggestion/ask to be able to set temperature from 8:15. If the set points cannot be set in shorter time span than one hour, I just set one to 7:15 which is irrelevant, and the second one to the final hour from which we would like to be able to control it via thermostat.

 

 

Finally, could we start from the very beginning and could you write, what exactly would you like to accomplish? I think that there is some misunderstanding between us in the matter how Heating Panel works. So could you write, what do you want to do with this schedule and what is not possible? 

 

I use a Heatit theromstat.

In your scheme I can oly change temp from 8:15 to 18:00 , HC2 is set on none ,but if I come home at 18:30 and i want to set my thermostat to 23C it wont work my HC2 woud bring it back to 22C at next pol.

Even when i make setpoint at 19:00 to NONE i woud stil be in the overlap of one houre between stepoint , I woud have to use my phone to us manuel mode .

Please login or register to see this attachment.

1 minute ago, Jaapkooi said:

 

I use a Heatit theromstat.

In your scheme I can oly change temp from 8:15 to 18:00 , HC2 is set on none ,but if I come home at 18:30 and i want to set my thermostat to 23C it wont work my HC2 woud bring it back to 22C at next pol.

Even when i make setpoint at 19:00 to NONE i woud stil be in the overlap of one houre between stepoint , I woud have to use my phone to us manuel mode .

Please login or register to see this attachment.

The never had too change the panel the old one was fine  

I rather see a checking box that enables (After setpoint made ,set temp to none.)

[I.Srodka 4]

You can just set to NONE the next range, so there is no overlap?

 

There is "none" from 8:15 to midnight here:

Please login or register to see this attachment.

[Jaapkooi 1]

3 hours ago, I.Srodka said:

You can just set to NONE the next range, so there is no overlap?

 

There is "none" from 8:15 to midnight here:

Please login or register to see this attachment.

Hi  

yes that's true But I do not have my temp at 22C on 18:00.

 

I thank you for your time to understand me ,but te fact is when setpoint 3 is on temp 22C  time 18:00 and setpoint 4  temp none time 19:00 ther is one hour that i can not change my temp on my thermostat.

And if i do the HC2 will put it ( in that hour 18:00 to 19:00) back to 22C ,i would have to use the manuel mode in HC2 to keep it on 23C .

 

[I.Srodka 4]

Hi agan, @Jaapkooi!

 

Could you write down, without using Heating Panel, how do you want your heating to be set? Write ranges, times, hours, and what and when should be turned on in a very clear manner.

[mortesan 9]

It would be better if the heating panel only changed the temp on a device on the time zones, not every minute, that way we could change it in between for example direct on the HeatIt thermostat without having to use manual mode. I am running a scene to change night/day temp in my living room, this way I can control it manual in between but it will always be changed at day/night. 

A good solution would be to bring in a check box in the heating panel called for example "force temp", checked would mean heating panel had full control and forced temp even if people tried to change in app or on thermostat(like it is today). Unchecked would mean heating panel only changed temp at time zones, and we could do what ever we wanted in between. 

 

 

 

 

 

Edited October 24, 2017 by mortesan

[Jaapkooi 1]

9 minutes ago, mortesan said:

It would be better if the heating panel only changed the temp on a device on the time zones, not every minute, that way we could change it in between for example direct on the HeatIt thermostat without having to use manual mode. I am running a scene to change night/day temp in my living room, this way I can control it manual in between but it will always be changed at day/night. 

A good solution would be to bring in a check box in the heating panel called for example "force temp", checked would mean heating panel had full control and forced temp even if people tried to change in app or on thermostat(like it is today). Unchecked would mean heating panel only changed temp at time zones, and we could do what ever we wanted in between. 

 

 

 

 

 

Your my man thanks

4 hours ago, Jaapkooi said:

 

I use a Heatit theromstat.

In your scheme I can oly change temp from 8:15 to 18:00 , HC2 is set on none ,but if I come home at 18:30 and i want to set my thermostat to 23C it wont work my HC2 woud bring it back to 22C at next pol.

Even when i make setpoint at 19:00 to NONE i woud stil be in the overlap of one houre between stepoint , I woud have to use my phone to us manuel mode .

Please login or register to see this attachment.

The never had too change the panel the old one was fine  

I rather see a checking box that enables (After setpoint made ,set temp to none.)

 

[antamaga 0]

On 24/10/2017 at 3:17 PM, mortesan said:

It would be better if the heating panel only changed the temp on a device on the time zones, not every minute, that way we could change it in between for example direct on the HeatIt thermostat without having to use manual mode. I am running a scene to change night/day temp in my living room, this way I can control it manual in between but it will always be changed at day/night. 

A good solution would be to bring in a check box in the heating panel called for example "force temp", checked would mean heating panel had full control and forced temp even if people tried to change in app or on thermostat(like it is today). Unchecked would mean heating panel only changed temp at time zones, and we could do what ever we wanted in between. 

 

 

 

 

 

 

Hi,

 

using the heating panel,

 

if I want to manually change the temperature for a period (eg 1h) from the thermostat or app, with the current version being no longer possible?

 

[mortesan 9]

55 minutes ago, antamaga said:

 

Hi,

 

using the heating panel,

 

if I want to manually change the temperature for a period (eg 1h) from the thermostat or app, with the current version being no longer possible?

 

Yes it is possible but only in app with zones and manuel mode

[antamaga 0]

on the app I no longer find the timer ...,

and from the thermostat in the house?

[pos 22]

Where did the Fibaro people go? Did they just leave the ongoing thread they were involved in?

[Jaapkooi 1]

No the did not I think the did something with it  ,Thanks

On 24-10-2017 at 3:06 PM, I.Srodka said:

Hi agan, @Jaapkooi!

 

Could you write down, without using Heating Panel, how do you want your heating to be set? Write ranges, times, hours, and what and when should be turned on in a very clear manner.

It works now ,Thanks