Scene with a motion sensor and lighting misbehaves

[Berne 0]

Hi,

 

I have programmed a fibaro motion sensor. according to the scene below.
When the time is over after 240 seconds, and I am still in the room, the lighting is no longer on. The fibaro motion does react, but does not switch on the lighting. What am I doing wrong?

 

Thanks in advance

 

Regards Ben

Please login or register to see this attachment.

[Reinhold 18]

You must delete the last line, and bij putting on (aanzetten) you must set the time on 240. That must working if i have right. 

Please login or register to see this attachment.

[Thomasn 77]

I would make it in lua to make sure that the motion device will rediscover movement after some time. I have never trusted blocks to trigger more than one instance.

[Reinhold 18]

@Thomasnhe has a Fibaro lite. They don't have lua?

Edited December 8, 2017 by Reinhold

[Thomasn 77]

19 minutes ago, Reinhold said:

You must delete the last line, and bij putting on (aanzetten) you must set the time on 240. That must working if i have right. 

Please login or register to see this attachment.

 

Then the light is not turned off again.

15 minutes ago, Reinhold said:

@Thomasnhe has a Fibaro lite. They don't have lua?

 

Ahh, yes. Lua and HC light is like water on a goose’s back.

[Reinhold 18]

But the red block, if you put here 240 the licht is on for 240s. Or am i wrong?

[Berne 0]

Please login or register to see this code.

Please login or register to see this code.

[Thomasn 77]

1 minute ago, Admin said:

Please login or register to see this code.

Please login or register to see this code.

 

Exactly. It is a delay connected to the block. I think you got it right in your first attempt. But I use lua and is not familiar with blocks. As I see it, you need something to trigger the scene again after the lamp has been turned off. 

How about trying this: lux sensor first, motion second...

 

 

 

Please login or register to see this attachment.

[Reinhold 18]

Your right, the first attempt was right i was thinking wrong. Forget what i said in my first post.

I was trying it too but the scene was not activated if the motion sensor is triggered. 

[Berne 0]

thanks for your reaction Thomasn, but this is unfortunately not the right solution. I think the LUX value is lagging behind. if the light is on, 0 LUX is indicated. and if the light is off, 180 LUX is indicated, so the light does not go on, how can I adjust this?

 

 

Please login or register to see this attachment.

Please login or register to see this attachment.

[Reinhold 18]

@Berne

I have found this, i don't know if you have already the answer. 

 

 

[Gareth Sheriff 0]

On 12/29/2017 at 9:58 PM, Reinhold said:

@Berne

I have found this, i don't know if you have already the answer. 

 

 

 

I have a scene with a fibaro motion sensor and a fibaro Dimmer 2. Does anybody know what can be done to overrule the scene once the light has been switched on manually at the Switch? 

Please login or register to see this attachment.

[Reinhold 18]

I think that can not be done in block scenes. You must make a lua scene.

 

 

[Gareth Sheriff 0]

Just now, Reinhold said:

I think that can not be done in block scenes. You must make a lua scene.

 

 

 

Not familiar at all with Lua, wouldn’t know where to start.

[Reinhold 18]

unfortunately I am not that good with lua. But I think there is someone here who knows the answer. 

[Gareth Sheriff 0]

9 minutes ago, Reinhold said:

unfortunately I am not that good with lua. But I think there is someone here who knows the answer. 

 

9 minutes ago, Reinhold said:

unfortunately I am not that good with lua. But I think there is someone here who knows the answer. 

 Thanks