Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

cannot activate the end coupling to the outputs ?


Question

Posted
268/5000
 
 
 
Hi there

I have a question about the smart implant.
Is that correct that I cannot activate the end coupling to the outputs in digital mode of IN1 and IN2?
With my HC3 I did not know whether the option was offered.
Greetings from the Sauerland

11 answers to this question

Recommended Posts

  • 0
Posted

It should be the same as in HC2. It depends on Smart implant configuration and not controller.

  • 0
  • Inquirer
  • Posted
    384/5000
     
     
     
    384/5000
     
     
     
    Hi there
    So far that's right.
    I need 2 digital inputs and 2 digital outputs.
    However, the outputs should be decoupled from the inputs.
    In the HC3 there should be an option that controls this.
    I can only get this set if I switch the inputs to analog.
    Do you have any idea whether this only works or whether it works the way I would like it to?
    • 0
    Posted

    You need to see if it possible in Smart Implant configuration.

    • 0
  • Inquirer
  • Posted

    Hi there

    I had already checked the documents and it says the following:

     

    Please login or register to see this attachment.

    Please login or register to see this attachment.

     

    That is what irritates me.
    First it works and then again not.
    I understand it as:
    It is coupled without any special procedure and if you use a different software address I can end-couple it.
    Since there is just such an option in the HC3 and it works with analog, my question was whether it would not work with digital.
    I already had a broken SmartImplant, so I'm a little careful with the get or it doesn't work.

     

    • 0
    Posted

    Hey, I have the same problem. Any solution to decouple the input with the output?

    • 0
  • Inquirer
  • Posted
    151 / 5000
    Good Morning
    Yes, the problem was done with the update of the HC3.
    Now you can separate the outputs from the inputs by setting.
    Greetings Frank
    • 0
    Posted (edited)

    @FBerges

    Good evening neighbour.

    If I understood you correctly you would seperate IN1 and IN2 from the outputs. if not my excuses.

    Just added an SI to my HC3. Can use the 2 inputs seperate from the outputs.  Can also switch the outputs by webbrowser or by scene.

     

    Please login or register to see this spoiler.

     

     

    Hopefullly this helps, if not please ask again.

     

    Have one SI in use with coupled output for my doorbell. And the other input is connected to a switch to check if the door is locked.

    I cannot disconnecd the ouputs anymore, without exclusion/inclusion. or maybe hard reconfig, because the sliders to disconnect/connect the outputs are vanished. Think its a feature. ?

     

     

     

     

     

     

     

     

     

    Edited by Flash
    • 0
  • Inquirer
  • Posted (edited)

    Good evening

    Yes, if the outputs are separated from the inputs, the inputs and the outputs have separate IDs.
    This means that they can also be used like all other IDs.
    Try it out it works fine.

    Greetings to the neighboring country stay healthy!
    Frank

     

    PS.

    This is exactly how it works with the FGS-224!

    Edited by FBerges
    • 0
    Posted
    2 minutes ago, FBerges said:

    Good evening

    Oops replied on an old post, should be on the post of @Ruma, apperently to late in the evening.? sorry about that.

    • Like 1
    • 0
    Posted

    Hello,

    Old topic, i know, but:

     

    any idea if i can set this in home assistant? I don't have these parameters shown in HA.

    Would it be an option to buy an fibaro home center to configure these and the use in home assistant? Or would the settings not be permanent?

     

    Any imput would be welcome!

    • 0
    Posted

    @daad01

    You must adjust parameters 20/21 (IO1/IO2).
    If you have a SmartImplant connected to HA, join the HA community. You have to go to the development environment and send special commands to set up SI.
    Just a note. Buying a Fibaro controller will not help you in this (unless you plan to switch to Fibaro) :)
    Why?.. because adding SI under any other controller will reset it and these settings will be valid for that controller. Adding it again under HA will result in a reset and the need to set parameters 20/21 again.

    eM.

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...