Jump to content

Welcome to Smart Home Forum by FIBARO

Dear Guest,

 

as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.

 

As a member you can:

  •     Start new topics and reply to others
  •     Follow topics and users to get email updates
  •     Get your own profile page and make new friends
  •     Send personal messages
  •     ... and learn a lot about our system!

 

Regards,

Smart Home Forum by FIBARO Team


  • 0

what parameter for walli roller shutter for venetian blinds


Question

Posted
i'm using the box HC3 and i want to drive my external venetian blinds with walli roller shutter , with a button FGWR-111 
I tried without success.  
 
I set FGWR-111  as a venetian blinds and perform a calibration (the module is marked as calibrated) 
with this setting how could i manage the slat ?   long clic/push doesn't position the slat and return a red ring. 

12 answers to this question

Recommended Posts

  • 0
Posted

@jluc2808Can you controll the blinds with the yubbi app? Do you see the 2 sliders for up/down and the slats?

  • 0
  • Inquirer
  • Posted

    i could see the 2 sliders (level and slat) on the app yubi, but my problem is with the button, i couldn't set the slat position with it, up / down are OK but long clic return a red ring and doesn't move the slats. 

    • 0
    Posted (edited)

    @jluc2808In my case, it helped to set in the general settings, the categorie to blinds, and the rolle to venetian blind. Look below. If you change this settings, I recommend to run another calibration.

     

    Edited by Fabir
    remove Data
    • 0
  • Inquirer
  • Posted

    @fabir it's exactly my setting 

    • 0
    Posted

    @jluc2808In my case it is a RS3. You have a walli roller shutter. 

     

    Do you use Zwave engine ZW3 or ZW2? If you use the ZW3 engine beta, strange behaviour can happen.

     

    Not sure if this below would help:

    -run the calibration again

    -exclude / include the walli rs again with or without security

    • 0
  • Inquirer
  • Posted

    i am running zwave with HC3, so it's zw2

    - i will run a new calibration to see if that change something , as it's not at home i will do that tomorrow and report if that change something

     

    just a question :  do you use long clic to move slats  and short clic to move the blinds (up and down) ? is there so restriction  ? 

    • 0
    Posted

    @jluc2808With HC3 you can use zwave engine ZW2 or ZW3. 

     

    I've connected a double momentary switch to the Roller Shutter 3. Short and long click are working as you have descripted above.

     

    I've also a walli roller shutter in stock, but not used it so far. When I've time, il give it a try with one of my blinds.

    • 0
  • Inquirer
  • Posted

    i have a strange problem, when i open/close the BSO, once it's completly open/close , i need to clic 2 time to perform an action (up or down) 

    do you have this ? 

     

    with my walli,roller shutter i couldn't set the slats nothing append when i try to move the slats itself. 

     

    • 0
    Posted

    @jluc2808No I don't have that. The RS3 is working as expected. 

    • 0
  • Inquirer
  • Posted

    @Fabir i suspect that all my problem are because my zwave engine version is 3.0, so i have to reset to go back to 2.0 and reconstruct all the jobs 🤮

    • 0
    Posted

    @jluc2808Good luk.

    • 0
  • Inquirer
  • Posted

    OK, after a 2 long days of hard work, i now have my config under Zwave engine V2, so i could ask for all the little problem i still encounter 

    - with Walli Controller (wired with 24v DC) i want to manage BSO with FGR223:

             * when BSO reaches the top or bottom end i need to clic twice to perform an order (up or down)

    => for this problem i never find a way to bypass the problem , If somebody have a solution or give me a way to bypass ?

     

    - with Walli Controller (wired with 24v DC) and light with FGS223:

             * when several Walli Controller are associated with the same light (same endpoint of FGS223) there is no synchro between them 

               if enter a command (on or off) on one walli, the other doesn't know that the light has changed his state, so i need to clic twice to reset the right state. 

    => for this 2nd pb i make a workaround with a scenario rather than association 

     

     

    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.

    Guest
    Answer this question...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×
    ×
    • Create New...