how do I add the roller shutter blind to the 12v driveway gate motor?

[kgm 0]

I am trying to add a roller shutter 3 to my 12 v gate motor, would like some advice if ti can work and how would I be able to wire it?

 

Attached is a picture of the controller any help will appreciated. I have not seen a videos on this,

Please login or register to see this attachment.

[Martin_N 148]

@kgm

Hello.
Even if I were to ignore all the safety and features that your door operator has, you will run into one thing. RollerShutter3 is for operation with 230V. Not 12V.
Switching the phase to all outputs.
You can try competing products.

[kgm 0]

will the Fibaro Implant work?

 

[Martin_N 148]

@kgm

 

This will help you. It is a monul designed for a similar case, i.e. controlling a DC motor by changing the polarity.

Qubino Roller Shutter DC 12/24V Z-Wave - type ZMNHODx (x = frequency).

 

5 minutes ago, kgm said:

will the Fibaro Implant work?

 

If you want to replace the existing door controller, only with Qubino Roller Shutter DC 12/24V.
However, if you only want to add control to the existing installation, you can use Smart Implant. So what do you require?

eM.

[kgm 0]

additional control only.

Would I able to power the RSB via 230 volts and then only use the s1, s2 to open and close the gate?

 

As I have the open and close input in my existing gate controller as in the pic?

 

Edited June 27, 2023 by kgm
added detail

[Martin_N 148]

@kgm It is not appropriate to use RS3 for such things. You need a potential-free contact, such as the FGS-214/224 or SmartImplant.
You can supply SmartImplant with 12VDC from the aux output of the opener. If you want to power the module from 230V, you can use FGS-214 or FGS-224.
I recommend the SI. It is small, undemanding, contains 2x input and 2x output.

[kgm 0]

thank you, really appreciated

 

[kgm 0]

HI all

I did get a Fibaro universal sensor, any one can assist me with a wiring it up to  my gate motor, a diagram would be helpful

 

 

 

[kgm 0]

POwer to aux output

Grnd to - 12v

i1 to open

i2 to close, 

 

Will this work?

[Martin_N 148]

4 hours ago, kgm said:

POwer to aux output

Grnd to - 12v

i1 to open

i2 to close,

 

Will this work?

POwer to aux output //yes

Grnd to - 12v //yes

i1 to open //no

i2 to close, //no

 

Will this work? //Summary: no

 

Do you really have a universal binary sensor from Fibaro or a Smart Implant?

 

To open, you must connect UBS OUT1 to the opening input, to close UBS OUT2 to the opening input.

BTW, UBS in1 or in2 can be connected to a wall switch for local control.

[kgm 0]

universal binary sensor from Fibaro

Also, howdo I setup on my home centre inter face to open or close

 

[Martin_N 148]

@kgm

Ok,... that's easy. Connect OUT1 UBS to COM on the opener. Another terminal OUT1 UBS with terminal FRX or TRG opener. Then configure the opener appropriately. You may already have a wireless control receiver on your FRX. In that case, connect in parallel to its contacts (COM / FRX).... Voila... and the job is done.

Now just configure in HC.

Unfortunately, I don't have UBS, so I can't help.

Just a little advice. Be sure to configure the automatic shutdown of the output after a time, for example 1 sec.

eM.

 

[BallaBooYeaH 0]

Anyone get a solution to this?  I now have the same gate and cant get RS3 working on it.

 

[Tim__ 116]

As stated above, RS3 is for mains voltage only.  I hope you haven't fried your gate controller!

 

Use a Smart Implant, diagram 9 from the manual. My guess is that you want to connect the Smart Implant output to "Trg" (trigger?) and AUX IO. 

Please login or register to see this link.

[BallaBooYeaH 0]

I have now got this working with a Smart implant.

[Martin_N 148]

Congratulations... but what's the message? That SmartImplant is suitable? Yes, it is - it's a similar device to the UBS and it's my favorite device.

Ave Smart Implant. 🤗