Welcome to Smart Home Forum by FIBARO
Dear Guest,
as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.
As a member you can:
- Start new topics and reply to others
- Follow topics and users to get email updates
- Get your own profile page and make new friends
- Send personal messages
- ... and learn a lot about our system!
Regards,
Smart Home Forum by FIBARO Team
Search the Community
Showing results for tags 'swiid'.
Found 6 results
-
Hi @tecmatic, @stevenvd, @joamlin, @cuprum, @acasanova @UrSv From what I read on the forum all or some of you have experience with this device I really liked the look and they are perfect for lamps and as such I have 7 of them and have been mostly happy with them. I have always has a few issues where they appeared dead but since 4.120 this seems to have gotten much worse and an exclude/include doesn't seem to resolve I'm running fw 1.82 on the cord switches I looked for templates but couldn't find them and the advanced tab didn't have a section to all manually is anybody else experiencing these issues and are they are any suggested solutions ? Thanks -f
-
Assoication/Report status back to controller
lasseruud posted a question in Other Devices / Third-party devices
I'm trying to tune my z-wave installation. I have LAMP1 connected to a Fibaro On/Off Switch. I have LAMP2 connected to Swiid Cord Switch. According to the manual of the Swiid, on LAMP2 I have set association group 2 to my Fibaro Home Center, so when I turn the lamp on/off with the button, the status is reported back to the Home Center. Now, I have created an association that makes the On/Off Switch of LAMP1, also turn on LAMP2. This works, but the status of LAMP2 (with Swiid) is not reported back to the Home Center. The status of LAMP1 (with Fibaro on/off) is reported back to the HC2. How can I make the Swiid report it’s status back when I turn it on/off through an association from another device ? The 2nd association group of the Swiid is associated with my Home Center. -
Hi @tecmatic, @stevenvd, @joamlin, @cuprum, @acasanova @UrSv From what I read on the forum all or some of you have experience with this device I really liked the look and they are perfect for lamps and as such I have 7 of them and have been mostly happy with them. I have always has a few issues where they appeared dead but since 4.120 this seems to have gotten much worse and an exclude/include doesn't seem to resolve I'm running fw 1.82 on the cord switches I looked for templates but couldn't find them and the advanced tab didn't have a section to all manually is anybody else experiencing these issues and are they are any suggested solutions ? Thanks -f
-
HI, Over the last few releases I've had to to exclude and re-include many of my swiid inline cord switches. I was wondering if anybody else has these inline cord switches and has experienced that same issue Thanks -f -
Hi, Does anybody know if the SwiidInter Inline switch is officially supported by Fibaro and has its own template ? Device is here - http://www.vesternet.com/z-wave-swiidinter-cord-switch Thanks Frank
-
Hi all, I've purchased the Swiid cord switch, which is a binary switch and therefore not able to communicate back the state of the switch. Right now the status in HC2 interface and Fibaro mobile app is only updated correctly when I turn on/off the switch through the HC2 interface or through the Fibaro app on my mobile device. Once I power on/off the switch manually by pressing the switch, the status change is not noticed by HC2 ofcourse. Although this behaviour is normal for binary switches, it is a bit annoying because when I manually power off the switch while HC2 still believes it is on, the power consumption report gets poluted with wrong data, plus it sometimes is also confusing to understand when you are on a remote location whether the lamp is actually on or off. I read on the web that it is possible to create a virtual device for this switch, which then allows me to get realtime status changes communicated through this virtual device (.. by some additional coding). Is this possible, and if yes, how to set it up and what additional code I need to use? Anyone maybe able to help me out? Thanks and best regards, Mark