Update HC2 4.023 BETA

[I. Szymanski 0]

Fibaro Home Center 2 v 4.023 BETA.

Beta version is designed for user testing and soon will be released as official.

WARNING! After installing this upgrade backups from version 1.x and 3.x will be retained but hidden because they are incompatible with the version 4.x. In case of update from old version, v1.x, after that update all users will be deleted. Admin password will be reset. Also update to Beta software all devices will be automatically reconfigured to work with new system architecture. Reconfiguration progress will be shown in pop-up window.

This update can last longer than previous. If this update lasts longer than 30 minutes, please go to main HC2 address (e.g. 192.168.0.1).

If "System temporarily unavailable" text will appear during update, please wait - you will be redirected to the main page when all services start.

4.023:

New Features

Soft Reconfiguration option allows you to save settings, parameters and device ID. Thanks to that scenes with reconfigurable device will not require editing. Full reconfiguration will remove and add the device to the Z-Wave network, resulting in the loss of its settings, parameters and change the device ID.

Resolved Issues

#0001986: Not able to change params

#0002126: New Switch reconfigure Problem

#0002189: Danfoss LC13 E5 error after few days.

Fixed problem with some Z-Wave locks battery reports

Fixed problem with controlling blind lamels via web interface

Communication with Satel devices improved (response time reduced)

Known issues

Important! User Developed Plugins will be removed with this update. Please be sure you have your plugin source code.

Satel - adding plugin progress bar disappears during configuration. Please wait about 15 minutes before performing actions on Satel devices.

Devices Polling may not work properly - devices state in UI may be refreshed only after action taken.

Breached sensor with Arm Delay causes instant alarm after being armed

Data range selection in event panel doesn't work properly

Devices imported via Gateway Connection may have no icons

Gateway Connection status of dead device between master and slave controller may be different

Devices not properly configured on 3.X may not be converted properly

Reconfiguration may not work properly in some cases

On mobile clients devices may be visible in different categories than configured

Advanced settings for some imported devices may not work properly

Plugin for Sony TV will not work with newest Sony Firmware

Horstmann Thermostat HRT4-ZW higher battery usage in some cases

Doorlocks some functions may not work properly

4.022:

New Features

Remote access is available for this version.

Resolved Issues

#0001513 RGBW custom created programs

#0001640 sceneActivation trigger doesn't seem to work

#0001681 Add / remove device continuous loop

#0001772 the remote control (KFOB2) we as a dimmer in Fibaro HomeCenter2 indicated

#0001898 Greenwave 6-socket plug shows as 7 switches

#0001924 beta 18 can not save scene with lux as a trigger (fibaro pir)

#0001931 HRT4 ASR UNIT not work in the Version 4.xxx

#0002000 Danfoss LC13

#0002032 Danfoss LC13 marked dead moments after status shows as "device is awake"

#0002081 FGRGBWM-441: Cannot turn on/off using mobile applications

Fixes for Z-Wave locks (Yale, FollowGood, Schlage)

Fixes for Z-Wave thermostats

Fixes for 3.x -> 4.x conversion process

Issue with backup compatibility

4.021:

Resolved Issues:

#0001844 HRT4-ZW and ASR-ZW not working, causing the heating system to burn continously

#0002026 SSR-303 not properly recognize

#0001958 After recovering backup all devices where online. Now all battery devices has become dead

#0002095 After upgrade V3 to 4.019 random dead nodes appear

#0002087 Nodes marked as dead, but functioning.

#0002036 Wrong spelling in Delete Device window: "Learing" instead of "Learning"

#0002139 4.020 Horstmann hrt4 can not set association

incorrect values returned by fibaro:getValue (LUA)

Horstmann Thermostat HRT4-ZW does not save the association

Many other minor fixes

4.020:

New Features:

Pre-Update Confirmation - installing update on 4.020 or newer will prompt user additional confirmation.

Mesh Network Reconfiguration - available on Configuration -> Z-Wave Network

Fixed Issues:

Incidental marking devices as dead

Horstmann Devices support

Many other Z-Wave engine fixes

4.019:

New Functionalities:

- Configuration > Backup now is Backup & Recovery

- Recovery Memory Status - can be checked on Backup & Recovery

- Backups - information about compatibility with current HC version

Resolved Issues:

#0001359: For some reason 1 smoke sensor doesnt show black box info.

#0001524: 3.902 Alpha - HUE plugin won't create new user

#0002037: Cannot delete device, but after a restart the devices shows as being deleted

#0002048: JSON ENCODE / DECODE doesn't work properly

#0001920: [ERROR] 09:23:47: line 44: attempt to index global 'json' (a nil value)

#0001699: panel energii

#0001849: Fibaro Door and Window Sensors do not report

#0001852: Unable to delete devices

#0001861: Since upgrading no scenes work

#0001877: HC2 stops working on 4.017

#0001709: When adding Foscam generic camera to plugin the password field is misspelled "Passwrod" should be "Password"

#0001824: Aeon Switch with energy meter. No more energy measurement/logging after upgrade to 4.017 beta.

#0001935: Notification of the battery status

#0001963: Event panel refreshed while browsing

#0001869: Fast scrolling in event history

#0001894: Log messages do not span columns

#0001655: Changing pages results in spinning wheel

#0001815: Power calcutaion is only working in rooms with Fibaro Wall plugs

#0001790: Virtual Device icon change causes a crash

#0001834: Get error 502 and 503 after virtual device import

#0001701: Controlled device is set to Air Conditioner on dimmers

#0001962: UI crashed after creation of magic scene

#0001966: setting " How frequently GPS position from the user?s iPhone should be collected" is not saved after reboot hc2

#0001888: Execution of lua commands

#0001907: Danalock POL_ZES100 (Z-Wave Danalock Square) sowing but not functional

#0001596: universal sensor has not the normal picture and dallas 18b20 temp does not work

#0001652: uni bin sensor breach scene does not work

#0001548: Nie działa triger włączenia włącznika Duwi

#0001812: HC2 doesn't respond anymore

#0001593: Email address validation wont allow + to be used

#0001651: HTML special characters being displayed in Virtual Device code

#0001946: fibaro:getSelfId does not work

#0001889: Unable to debug slider code

#0001992: FGK-101 with a DS18B2

#0002005: After creation of a magic scene i'm unable to login to the fibaro home center (keeps loading)

#0002023: Disarm sensors with scene

4.018:

Resolved Issues:

#0001566 All versions of FIBARO cannot support the switch state to return to the "Multilevel Switch Command Class, version 2"

#0001576 Untranslated text in Satel input/zone page

#0001578 Cannot change label value

#0001618 HSP02 no longer has parameters

#0001624 no different color for slave devices

#0001630 Reconfiguration did not run on a dimmer, resulting in no "sceneactivation"

#0001631 Roller Shutter 2 scene won't close

#0001711 Danfoss LC13 and older model are dead or E5 on the Danfoss itself

#0001773 Danfoss LC13 no Icon displayed

#0001747 Weather display wrong place

#0001834 Get error 502 and 503 after virtual device import

#0001836 Lili

#0001853 After upgrade web interface is slow when changing views

#0001873 No push messages possible on iPad/iPhone with 4.017

#0001880 Not able to set Variable manually anymore

many other fixes

4.017:

New functionalities:

User's Plugin Installation - ability to build and install Home Center plugin

FGHC Rest API Active Documentation - documentation and ability to test REST API requests, access at HOME_CENTER_IP/docs

Added support for American English (EN-US)

Plugins:

Nest - plugin for well-known thermostat

Netatmo - plugin for thermostat and weather station from netatmo

3.907:

This version mainly concentrate on adding better support and integration for more devices (not only z-wave device).

Important part of software responsible for management z-wave devices was rebuild from the scratch for better support different devices types.

New Home Center software introduces support for plugins. Plugins give support for new devices and new functionalities without modifying HC Firmware. Plugins can be used for controlling devices via different protocols and standards like TCP/IP, IR*, RS 232*, UPNP. Plugins have their own user interface and can call all APIs available on HC2. Possibility of building plugins by independent developers will be introduced in next versions.

* required additional hardware.

New functionalities

--------------------------

Drag & Drop for devices and scenes - available on home, devices and rooms screens. Assigning devices to rooms and changing its order is now much easier and faster.

Magic Scenes - new, simplified and easy to use graphical way to create scenes based on condition > action flow.

Temperature Panel - allows to see history of temperature changes in rooms and on each device.

Diagnostic Panel - general information about HC working condition like CPU & RAM usage, free space on hard drive. Will be extended in future versions.

New Z-Wave engine - redesigned and rewritten from the scratch. Now is faster and has better support for devices.

Z-Wave Door Locks support - controlling and PIN settings.

Thermostats - extended controlling for thermostats from manufacturers like: Honeywell, Trane Corporation.

Extended tamper for sensors - exclusive information for motion detection and violation of sensors.

Fibaro Smoke Sensor extended support - level of smoke and gap to alarm level is reported and visible on charts at iPad and Web Page. Sensitivity level is now easier to set.

Fibro Motion Sensor new device - when seismometer mode is turned on new device reporting tremors is available. Charts for temperature and illuminance. Additionally information about sensor violation.

Device hiding - device that is not in use can be hide without removing it.

Device deactivation - deactivated device is visible in UI but can't be controlled.

Multithreading added for HC (server and z-wave) - now engines work much faster.

Event panel moved - for better usability now is available in menu on right side of screen.

User rights management - moved to Configuration.

Block Scenes improvements - for device only available actions are visible, scene activation block added and logical conditions grouping using brackets.

Lua Scenes - updated tooltips for devices.

Plugins:

Plugins are grouped in categories: Safety, Cameras, Climate, Multimedia, Others

Plugins search

Network devices search via ARP

Plugins category Safety:

DSC Alarm - for DSC Alarms,

Helios Basic - integration using Basic license,

Helios Gold - integration using Gold license

Mobotix - for Mobotix videophone,

Satel Alarm - for SATEL

Plugins category Cameras

more than 100 devices from various manufacturers

Plugin category Climate

Carrier Furance

WS Davis Vantage

Plugins category Multimedia

LG Bluray

LG TV

NC + mediabox

XBMC Remote Control

Denon Amplifier

LG Bluray

Onkyo Amplifier

Philips Bluray

Pioneer Amplifier

Samsung TV

Sonos

Sony Bluray

Sony TV

Plugins category Other

Philips Hue

Wake on LAN

Other changes

Many other improvements to the system

Users who use version alpha from 3.901 to 3.906 need to perform recovery first and update from 3.590 after restoring backup.

[Guest Axel]

Hello,

I get this .... what does it mean ?

Not all devices added to the Z-Wave network are configured correctly. It is recommended to do the reconfiguration to ensure full functionality of the system..

Go to Z-Wave diagnostic panel

[ Added: 2014-12-17, 01:44 ]

AEON Multisensor....

[sj3fk3 27]

Could fibaro support maybe please help me? I've also filed a

Please login or register to see this link.

, but it might be something that I could fix myself?

I cannot edit the alarm scenes.

Please login or register to see this attachment.

Please login or register to see this attachment.

[UrSv 6]

I had to restart my HC2. Now it's back to power consumption NaNW but displayed OK values for a while. I'm not going to check the consumption panel today...

[KristianO 15]

I got some questions regarding beta and version 4.x

- Are Temp/smoke graphs avalible and can be filtered in time?

- Can variables be used as triggers within a scene? (Triggered via API)

- Can sceneblock handle OR condition (Brackets)?

- Can a scene be triggered only arming/disarming the alarm (not in comb. with breatch)

- Can eg. -30 min to sunset be used as trigger (Not only pased sunset)

- For how long in time is the evenlog stored?

[TANE 12]

Last night the bedroom lights turned on at 3:45:20

Did check the log for some triggers

Power save scene was started at 3:45:19.

This one only turns of some devices.

Scene is in use for longe time and did not have this before.

Very low WAF factor at that time..

[deanrparry 19]

And the scene does not have an accidental OFF > ON?

This is bad if it is sending the wrong command to devices! I have a 127db siren that my wife would murder me if that went off!

[TANE 12]

no just basic turn off

Please login or register to see this attachment.

[deanrparry 19]

Please login or register to see this image.

/emoticons/default_icon_eek.gif" alt=":shock:" />

[TANE 12]

Also checked the other triggers to be sure none of the turned off devices will trigger another scene.

[Guest Axel]

Still get these message:

"Not all devices added to the Z-Wave network are configured correctly. It is recommended to do the reconfiguration to ensure full functionality of the system..

Go to Z-Wave diagnostic panel"

At the diagostic panel there are several Devices without templates:

NorthQ Gas Metre

NorthQ Power meter

3 Düwi Power switches IP44

Reconfigure doesnt help !!!

Whats wrong ?

[jonny 0]

I have the same Axel (for the three devices that i can manage to add that is)

[deanrparry 19]

I think that devices with no templates etc will always be listed there? It seems only Fibaro devices are not listed there! Maybe they do not want you using other people products

Please login or register to see this image.

/emoticons/default_icon_wink.gif" alt=";-)" />

[treboR 3]

I've got 3 TKBhome dimmer switches and they are not reconfiguring as well. The Danfoss LC13 ran without any problems after sending a wake up twice.

/Edit

I just discovered that if you are using an older phone app ( in my case an IPhone 4S with an older version of IOS so also an older Fibaro app version ) was causing the 503 error.

Anyone else running an older IOS app version to test?

[Guest Axel]

Hi,

please back to 4.022.

More and more moduls mak problems.

HC2 stops working, have to restart using power cable.

Axel

[petergebruers 1,268]

Please add your information to

Please login or register to see this link.

It is easier to track issues across versions...

[TANE 12]

Last 32 hour stable.

Removed the scene that possibly turned on the lights last night.

Rebuild again..

Possible conversion problem..and in the scene turn off there where some devices that did not exist on the HC2

[deanrparry 19]

36hr

Please login or register to see this image.

/emoticons/default_smile.png" alt=":)" srcset="https://forum.fibaro.com/uploads/emoticons/[email protected] 2x" width="20" height="20" /> and not as much as a glitch up to now!

[alandee 79]

Retried after removing non existant devices .. looks like no 503 this time so far .. .. w00t !

Cheers,

al.

[ Added: 2014-12-18, 11:57 ]

I can't seem to find any soft reconfigure options though ?

[ Added: 2014-12-18, 14:38 ]

I guess I didn't look very hard, cos they are there as plain as day

Please login or register to see this image.

/emoticons/default_smile.png" alt=":)" srcset="https://forum.fibaro.com/uploads/emoticons/[email protected] 2x" width="20" height="20" />

Running sweetly..

[hvb83 1]

wow, even Deanrperry seems happy. Now I might actually consider upgrading within the next few weeks.

Please login or register to see this image.

/emoticons/default_icon_mrgreen.gif" alt=":mrgreen:" />

[fuuss 25]

best comment ever

Please login or register to see this image.

/emoticons/default_icon_smile.gif" alt=":-)" />)

Please login or register to see this image.

/emoticons/default_icon_mrgreen.gif" alt=":mrgreen:" />

Please login or register to see this image.

/emoticons/default_icon_mrgreen.gif" alt=":mrgreen:" />

Please login or register to see this image.

/emoticons/default_icon_mrgreen.gif" alt=":mrgreen:" />

Please login or register to see this image.

/emoticons/default_icon_mrgreen.gif" alt=":mrgreen:" />