Welcome to Smart Home Forum by FIBARO
Dear Guest,
as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.
As a member you can:
- Start new topics and reply to others
- Follow topics and users to get email updates
- Get your own profile page and make new friends
- Send personal messages
- ... and learn a lot about our system!
Regards,
Smart Home Forum by FIBARO Team
Search the Community
Showing results for tags 'hclite'.
Found 4 results
-
Hi All of you, Does anybody have an idea how to connect a secure SRT321 and a Qubino flush on/off thermostat can be coupled? The goal is that the SRT should be the one to set the temperature and the Qubino should switch the electrical floorheating. Meanwhile the Qubino sensor should be able to measure the reached temperature. So f you set the temperature on the SRT to, for example, 25 degrees, it should switch the Qubino to on, if the measured temperature by the Qubino sensor is below the 25 degrees. as soon as the Qubino sensor measures 25 degrees it should switch of and ofcourse when the floor temperature comes below the 25 degrees it should switch on again.
-
associating aeotec wallmote / fibaro dimmers / homecenter lite
roelnic posted a question in Home Center Lite
Goodmorning, Please help me in the right direction. I bought a aeotec wallmote (4 buttons) and would like to use this wallmote to turn on / dim a set of lights (two fibaro dimmers 2). However I get lost in setting associations (endpoint, groups, master / slave / single / multi. I searched for a good explanation, but I couldn't find helpful documentation. I looked at wallmote documentation (groups and controls = https://aeotec.freshdesk.com/support/solutions/articles/6000162392-wallmote-quad-user-guide-) fibaro e-learning (http://e-learning.fibaro.com/topic/associations-in-version-4-x-2/) It's not completely clear to me how I configure the associations correctly: I have multiple 'wallmotes' (wallmote master, wallmote 0 - 4). I assume i have to set the association per wallmote button (device)? e.g. wallmote 1 (at this place the wallmote 1 is not available itself in the associations tab? You have the M and S buttons (I assume Master and Slave). How do I have to configure this? You have endpoint 0 and endpoint 1. What exactly is the difference. Is this fibaro specific (in the documentation of the wallmote as well as wallmote / vera UI7 i cannot find this Shoud i use single or multi? and where can I configure this? I really appreciate your reply! Specific tips related to this configuration or if you have good documentation avalaible about setting associations in general on the fibaro (endpoints, groups, M / S, best practices) are appreciated! Best regards, Roel -
Ściemnianie i rozjaśnianie z włącznika S2 bistabilnego Dimmer2
bratkrk posted a question in Sceny i Interfejs
Mam problem w sumie już od tygodnia z tym walczę. Szukałem na forum ale nic nei znalazłem. Mam dwie sceny 1] KeyID:20 OFF-ON scena ściemnia na 20% 2] KeyID:21 ON-OFF rozjaśnia na 80%. (Sceny na blokach w załączniku) PROBLEM: Jak jedna uruchomię to sceny uruchamiają się raz jedna raz druga i tak w kolko. Tak jakby włączanie scen przez KeyID 20 i 21 w jakiś sposób nie działało. Starałem się dodać zmienną żeby na druga scena nie startowała od razu i dalej nic. Dodatkowe pytanie o co chodzi w IF (L.Dzieciecy-pilot == KeyId: 21 0s) na końcu jest 0s czy to znaczy że sprawdza warunek po x sekund ? A co z warunkiem po "i" jest wykonywany wcześniej niż pierwszy warunek !? PS. Jestem nowy proszę o wyrozumiałość nie wymagam od razu rozwiązania oczekuję raczej wskazania gdzie szukać rozwiązania.
-
Hi, I'm experiencing synchronization issues: Setup is as follows: HC2: Main Gateway, 4.100 HCL: Slave Gateway, 4.100 Problem: devices from Slave sync into unassigned instead of in the right rooms and sections on the HC2. Tried removing and re-adding the slave, tried synchonising, tried importing, tried manual importing. Nothing seems to work. The only option I have to fix this is to manually re-assign every device from the slave to the correct rooms in the HC2. At one point I was thinking that I should remove all the rooms and sections from the HC2 that are handled by the HCL, thinking that upon synchronising they would get imported with the devices and with correct room mapping. Removed a couple of rooms from the HC2 and re-synched. No luck. Didn't try removing entire sections. Would rather wait for the feedback of Fibaro or the community. When working with a Master/Slave Gateway setup: should all sections and rooms of the slave gateway be manually configured in the master gateway? Or should they automatically sync from the slave to the master? Is this problem stemming from room and section conflict issues or is there something else going on? Any help? Thank you, APGC
