Welcome to Smart Home Forum by FIBARO
Dear Guest,
as you can notice parts of Smart Home Forum by FIBARO is not available for you. You have to register in order to view all content and post in our community. Don't worry! Registration is a simple free process that requires minimal information for you to sign up. Become a part of of Smart Home Forum by FIBARO by creating an account.
As a member you can:
- Start new topics and reply to others
- Follow topics and users to get email updates
- Get your own profile page and make new friends
- Send personal messages
- ... and learn a lot about our system!
Regards,
Smart Home Forum by FIBARO Team
Search the Community
Showing results for tags 'hvac'.
-
How to synchronize the mode, temperature and wind speed of two HVAC
Gee posted a question in Scenes and Interface
How to synchronize the mode, temperature and wind speed of two HVAC I can't find a way in the associated page. Is there any way to synchronize with LUA scenes or other ways? Thank you -
Daikin VRV HVAC HTTP virtual device control
Spenden posted a question in Other Devices / Third-party devices
I need to control a Daikin VRV multi-split HVAC system which has their intelligent touch controller with the HTTP interface option installed. To control each individual indoor unit I need to send an HTTP POST. Below is an example of the information the controller is expecting the HTTP POST to contain... Here is an example to get A/C "1:1-02" current status. HTTP Request POST /cmd/ HTTP/1.1 ¥r¥n Content-Length: 32¥r¥n Content-Type: application/octet-stream¥r¥n ¥r¥n 20 000000 {Command Size;32} 74 110100 {Command ID;70004} 00 000000 {Reserved 1} 00 000000 {Reserved 2} 04 {A/C Address to get status; 1:1-00 to 1:1-07 (1:1-02 is enable)} ------- 00 {A/C Address to get status; 1:1-08 to 1:1-15} 00 {A/C Address to get status; 1:2-00 to 1:2-07} 00 {A/C Address to get status; 1:2-08 to 1:2-15} 00 {A/C Address to get status; 1:3-00 to 1:3-07} 00 {A/C Address to get status; 1:3-08 to 1:3-15} 00 {A/C Address to get status; 1:4-00 to 1:4-07} 00 {A/C Address to get status; 1:4-08 to 1:4-15} Request Command (hexadecimal) 00 {A/C Address to get status; 2:1-00 to 2:1-07} 00 {A/C Address to get status; 2:1-08 to 2:1-15} 00 {A/C Address to get status; 2:2-00 to 2:2-07} 00 {A/C Address to get status; 2:2-08 to 2:2-15} 00 {A/C Address to get status; 2:3-00 to 2:3-07} 00 {A/C Address to get status; 2:3-08 to 2:3-15} 00 {A/C Address to get status; 2:4-00 to 2:4-07} 00 {A/C Address to get status; 2:4-08 to 2:4-15} --------- I am trying to create a virtual device for each indoor unit (room) and have looked at a lot of posts and tutorials and can’t find anything similar to point me in the right direction, so any ideas how to get this up and running appreciated... -
Hello fellow Automaters, I have a problem with a brand new ZXT-120 from Remotec that should control my LG AC unit. Before I found this device I had it set up with a dry contact from LG and a relay switch from Fibaro. It was only allowing me to turn the AC on or off to the state chosen by remote. It wasn't that bad but was also giving me many issues. Switching dry contact mode was disabling LG remote at all - so when time of the year was changing and I wanted to switch from heating to cooling it was very annoying to go through the process - especially that it wasnt very intuitive and required turning the POWER of the device off (which meant disabling electrcity at all in my apartment) But to the point: I have just received my new ZXT-120 from Remotec. The device HW version (found on the sticker) is 1.80. It is working in FLiRS battery mode. When I add it to my HC2 though (4.161Beta) it is being discovered as a version 1.20. I got 4 devices discovered (as per attached pic) and i can communicate with it. Version 1.20 codes only support 4 different codes for LG ACs (parameter 27), while version 1.80 supports 8 or 9 different codes. For me - only the 4 old codes are available from within HC2 parameter 27 (the max value set there is 512, while 1.80 new parameter codes exceed value of 512). The 1.20 old codes do not support some of my AC functions like FAN, and FAN Speeds. I am not sure that it also sends correct commands to my AC unit. I have tried to remove/add it 6 times already. Also With Wide Network Inclusion mode and without it. The standard troubleshooting I did included adding within 10 cm from HC2 and from normal location. It just discovers it as a version 1.20 and there is nothing I can do to change the required parameters. Version 1.80 has also additional code that is below 512 (464 - squared in the pic) but also not available for version 1.20 Has anybody faced that issue? Can you guys help please?
-
Automatic HVAC and Aircondition controller without IR
moosairshad posted a question in Scenes and Interface
Hi Friends, I am looking for HVAC and AC withour IR controllers. Is there any actuator and sensor compatible with these systems? Thanking you in advance -
I have a Panasonic Etherea AC unit funtioning with the Inthesishome box and this works perfectly with the Intesis native app over internet. Recently IntesisHome has launched their API (http://developer.intesishome.com) and that is great news for integrating this into the HC2. Is there someone who can help with: 1) explaning how an API from an external device can be reached best by the HC2: through lua scripting or php? 2) scripting php and/or lua code to setValue in the Intesis api? 3) setting up a plugin for this api (as the Intesis home box allows for controlling multiple brands of AC units)? Thanks.
- 7 replies
-
- plugin
- IntesisHome
- (and 6 more)