zigbee List of Zigbee devices - users for users

[K.Drozynski 106]

Dear users,

 

We know that you are eager to share your thoughts regarding all Zigbee devices that you have. With so many Zigbee devices available on the market it would extremely difficult to prepare a complete list of supported Zigbee devices which would  include useful remarks.

 

For this reason we would like to encourage you to share your thoughts with other community members - let's make this a list of tested Zigbee devices created by users for users.

 

As correctly pointed out by @petergebruers (kudos to you) "A nice list for Zigbee2MQTT already exists, complete with picture, reset procedure(s) and quirks:

 

Please login or register to see this link.

 

So we can add one of those 2149 devices to our HC3, test its behaviour and report back with a link to the EXACT same device.

It is important to link to the exact same devices as the one you tested because there are many lookalikes..."

 

Regards

 

[MJJ_ADE 2]

W dniu 30.05.2022 o 22:37, lukaszbobola napisał:

Tuya IG019 works good. Can be controlled, shows voltage and current.

But sounds very noisy

[R van Vuuren 0]

Hi Guys, 

Please login or register to see this link.

HC3 shows Added device in console and noted the extra device under the Zigbee Configuration tab but the device is not visible at all.

Same for:

Please login or register to see this link.

Please login or register to see this link.

 

 

[imparator 1]

On 5/15/2022 at 6:41 PM, sebo said:

Please login or register to see this link.

Blitzwolf BW-SHP13 works as expected

How did you include this ?

 

i have also this one but it doesn't include !

[mdrazek 0]

Philips Hue White Ambiance E27 9W LWA001 | firmware v1.101.2

 

Works as expected, I have added 3 bulbs.

Dimmer works perfert also.

 

Bulbs needs reset to factory state - 

Please login or register to see this link.

[mdrazek 0]

Philips Hue Smart Plug LOM002 | firmware v1.93.6

 

Works as expected but no energy metering.
It can be enabled or disabled.

 

Plug adapter needs reset to factory state, similar to this operation -

Please login or register to see this link.

[Sjekke 87]

The new beta has ensured that the Aqara P1 Motion Sensor is now recognised. That's where the story ends...  

 

Can you configure this device? Any suggestions?

 

[Asko 3]

Aqara wireless switch WXKG11LM

Adds to system, no errors in process but device shows as "not configured", battery status empty. No actions available for that device. If somebody has a solution then please let me know

[HenryEST 0]

SONOFF SNZB-02D

and

SONOFF SNZB-01

 

[ZIGBEE]: Device identification process started.

[ZIGBEE]: Device added to the network.

Configuration: Not Configured

 

HC3 5.131.52 (beta)

[De Colt 9]

Please login or register to see this code.

[Lucano99 0]

Please login or register to see this link.

Added as a unknown device

 

[mkresal 0]

On 4/14/2022 at 11:06 AM, petergebruers said:

Has anybody resolved the issue with the Ikea tradfri motion sensor - joining ok but status stays "never breached"?

 

On 4/14/2022 at 11:06 AM, petergebruers said:

E1745 IKEA TRADFRI motion sensor

Please login or register to see this link.

 

Does NOT work as expected: joins OK but then status stays "never breached"

Adds as "com.fibaro.motionSensor"

 

Edited February 14, 2023 by mkresal

[Henk Visser 0]

On 6/13/2022 at 9:37 PM, emielstroeve said:

Finally a decent outdoor sensor: Hue Motion Sensor: 

Please login or register to see this link.

Do I still need a Hue bridge or does it directly work with HCL 3 Fibaro?

[emielstroeve 22]

7 hours ago, Henk Visser said:

Do I still need a Hue bridge or does it directly work with HCL 3 Fibaro?

On HC3, Zigbee is supported so you can directly add a Hue motion sensor as a device. As far as I can tell, HCL3 doesn't support Zigbee so than you'll need to add the motion sensor via the hue bridge QA (don't know if that works)

[RobertL 21]

Hi

Have anyone tested this Heiman zigbee Smoke sensor with HC3  ?

Please login or register to see this link.

[wojofibaro 6]

Forget zigbee. Fibaro is not ready for it, and It will never be. Even if some devices working... it is unstable

[yoozef 4]

Aqara (Xiaomi) Water Leak Sensor SJCGQ11LM

Please login or register to see this link.

 

WORKS fine. Instantly reports detected leakage. Works also as temperature sensor but would require some calibration (didn't play with it yet if feasible or not).

[yoozef 4]

Guys, is there ANY zigbee device supported, that could serve as a wireless (battery powered) switch?

 

I know these DON'T work:

Aqara wireless switch WXKG11LM, WXKG13LM, ....

Sonoff SNZB-01

 

Is Fibaro's "the button" the only descent solution?

 

[max_fok 9]

Please login or register to see this link.

 

Gledopto RGBW Led Controller C-007P confirm working well on Fibaro HC3

its connector strips have plastic screws but it has the option to connect a converter adapter as it is shown bellow on image, it is better this way than messing around with the plastic screws😳

Please login or register to see this attachment.

Please login or register to see this attachment.

Please login or register to see this attachment.

Please login or register to see this attachment.

[max_fok 9]

On 4/11/2023 at 10:05 PM, yoozef said:

Guys, is there ANY zigbee device supported, that could serve as a wireless (battery powered) switch?

 

I know these DON'T work:

Aqara wireless switch WXKG11LM, WXKG13LM, ....

Sonoff SNZB-01

 

Is Fibaro's "the button" the only descent solution?

 

Unfortunately yes, except you want to mess around with Fibaro Keyfob to enable some scenes or switches.

Keyfob has many combinations, 2 times that keys, 3 times that key , pressing together two of the keys etc.

Please login or register to see this link.

[RSB 5]

On 4/14/2022 at 11:06 AM, petergebruers said:

LED1836G9 IKEA TRADFRI LED bulb E26/E27 806 lumen, dimmable, warm white

Please login or register to see this link.

 

Works as expected, is a "com.fibaro.multilevelSwitch"

 

E1745 IKEA TRADFRI motion sensor

Please login or register to see this link.

 

Does NOT work as expected: joins OK but then status stays "never breached"

Adds as "com.fibaro.motionSensor"

i recently bought 2 ikea e1745 motion sensor and i have the same problem. I told fibaro, they told me they will fix the bug in next update🤞